Studer Innotec XTH 5000-24, XTH 6000-48, XTH 8000-48 Accessories, RCC-02 RCC-03

Page 23

STUDER Innotec

Xtender

6.4 Accessories

6.4.1CONTROL CENTRE AND RCC-02/03 (REMOTE CONTROL) DISPLAY

An RCC-02/03 remote display and programming unit can be optionally connected to the Xtender via one of the two RJ45-8-type “Com. Bus” (3) connectors.

These connectors may only be used for connecting a CAN-ST compatible accessory, excluding any other connection such as LAN, Ethernet, ISDN, etc.

The RCC-02/03 control centre is vital for modifying device configurations. It also allows the following functions:

Display of function synopsis

Display of the measured operational values (current / voltage / power output, etc.)

Updating of software or implementation of customised software

Storage of inverter configuration

Updating of inverter configurations

Storage of error message history

RCC-02

RCC-03

The features of the RCC-02 and the RCC-03 are the same. They only differ in their external appearance. The RCC-02 is designed for wall mounting, whereas the RCC-03 is designed as a board device.

The RCC-03 model must be taken off the table to allow access to the SD card slot (during updating, for example).

Model N°: RCC-02: Dimensions: H x W x D / / 170 x 168 x 43.5mm RCC-03: Dimensions: H x W x D / / 130 x 120 x 42.2mm

The two remote control models are delivered with a 2 m cable by default. Cables of specific lengths (5 m, 20 m and 50 m) can be ordered.

The article no. is as follows: CAB-RJ45-xx. The length in metres is specified as xx

Up to 3 RCC-02/03 remote controls can be connected in series on the communication bus of one Xtender or an Xtender multi-inverter system. In a system comprising a single Xtender, the connection of the RCC-02 or RCC-03 may be conducted without stopping the Xtender (warm). When connecting an RCC-02/03 remote control in a multi-unit system, it is recommended that all units in the system be stopped and that the communication bus on the device on which the connection is being made be terminated.

The 2 switches for terminating the communication bus, “Com. Bus" (4) both remain in position T (terminated) except when both connectors are in use. In this case, and only in this case, both must be placed in the O (open) position. If one of the two connectors is not in use, the two termination switches (14) will be in position T.

Installation and operating Instructions

Xtender V1.3

Page 23

Image 23
Contents Xtender Table of Contents Operating instructions IntroductionGeneral information Conventions Quality and warrantyExclusion of Liability Storage Assembly and installationInstallation site Handling and movingConnections FasteningDescription Comment PosChoice of system CablingEarthing system Recommendations for dimensioning the system XTH3000-12 XTH5000-24 XTH6000-48 XTH8000-48 Wiring diagramsConnecting the battery Fuse on the battery sideBATTERY-SIDE Connection Connecting the Consumers AT the 230 V AC Output Connecting the battery Powering up the installationDescription of the main functions Circuit diagramDescription and functioning Fast voltage loss detection mode fast transfer Temperature is increased or the ventilation Limiting the Input Current by Limiting the Charger Current Input Current Controlled by Input Voltage Auxiliary Contacts Multi-unit configurations RCC-02 RCC-03 AccessoriesDisplay and control parts Indicated alarm CommentControl Main on/off controlCheck the cause of this excess voltage. The equipment will EC declaration of conformity Maintenance of the installationProduct recycling Comments of annexes’ figures Example of parallel connection of 2 or 3 Xtenders Example of installation in a vehicle AC partInstallation example in a boat, with isolation transformer Example of a hybrid installationElem Description Comment Figure elements DC partFigure elements AC part Elements of connexion cabinet a Type plate elements b Control and display parts for the Xtender bStuder Innotec Xtender Table of standard configurations Studer Innotec Xtender Model XTH 3000-12 XTH 5000-24 XTH 6000-48 XTH Technical data