Studer Innotec XTH 5000-24, XTH 6000-48, XTH 8000-48 operating instructions Pos, Description Comment

Page 8

STUDER Innotec

Xtender

Fig. 4a

7

5

1 2 3 A

 

B

6

1

2

3

4

8

1

2

AUX1

 

AUX2

 

AUXILLARY CONTACT

9

 

10

L1 L2 L3

11

12

14

 

13

 

 

 

L

L

 

AC Input

AC Output

Warning!

! Check battery polarity (+/-) before connecting A wrong connexion may damage the systen

OFF

ON

Main Temp. switch Sens.

Open Terminated

Pos.

Denomination

Description

 

Comment

 

 

1

ON/OFF

Main on/off switch

 

See chapter

The real time clock 7.1 - p

 

 

Main switch

 

 

24.

 

 

2

Temp. Sens

Connector for the battery

See chapter

6.4.2 – p. 24.

 

 

 

temperature sensor

 

Only connect the original Studer BTS-01

 

 

 

 

 

sensor

 

 

3

Com. Bus

Double connector for

 

See chapter 4.5.9 – p. 14.

 

 

 

connecting peripherals such as

The two termination switches (4) for the

 

 

 

the RCC002/03 or other

communication bus both remain in

 

 

 

Xtender units

 

position T (terminated) except when both

 

4

O / T

Switch for terminating the

connectors are in use.

 

 

(Open /

communication bus.

 

 

 

 

 

Terminated)

 

 

 

 

 

5

--

3.3 V (CR-2032) lithium ion type

Used as a permanent supply for the

 

 

 

battery socket

 

internal clock. See chapter The real time

 

 

 

 

 

clock 6.2.11 - p 21.

 

6

--

Jumper for programming the

See chapter 6.2.12 – p. 21 and fig. 8b

 

 

 

off/on switch by dry contact

point (6) and (7). They are positioned at A-

 

 

 

 

 

1/2 and B-2/3 by default

 

7

REMOTE

Connection terminals for dry

See chapter 6.2.12– p. 21).

 

 

ON/OFF

on/off remote connection.

When the control via dry contact is not

 

 

 

 

 

being used, a bridge must be present

 

 

 

 

 

between the two terminals.

 

8

AUXILIARY

Auxiliary contact

 

(See chapter 6.2.10– p. 21)

 

 

CONTACT

 

 

Take care not to exceed the admissible

 

 

 

 

 

loads

 

 

9

--

Activation indicators for auxiliary

See chapter 6.2.10– p. 21

 

 

 

contacts 1 and 2

 

 

 

 

10

L1/L2/L3

Phase selection jumpers.

See chapter 6.3.1. – p.22.

 

 

 

 

 

Jumper default at position L1

 

11

+BAT

Positive pole battery connection

Carefully read chapter 4.5 – p.12

 

 

 

terminals

 

Take care with the polarity of the battery

 

 

 

 

 

 

 

 

Installation and operating Instructions

Xtender V1.3

Page 8

Image 8
Contents Xtender Table of Contents Operating instructions IntroductionGeneral information Quality and warranty ConventionsExclusion of Liability Assembly and installation Installation siteHandling and moving StorageFastening ConnectionsPos Description CommentCabling Choice of systemEarthing system Recommendations for dimensioning the system Wiring diagrams Connecting the batteryFuse on the battery side XTH3000-12 XTH5000-24 XTH6000-48 XTH8000-48BATTERY-SIDE Connection Connecting the Consumers AT the 230 V AC Output Powering up the installation Connecting the batteryDescription of the main functions Circuit diagramDescription and functioning Fast voltage loss detection mode fast transfer Temperature is increased or the ventilation Limiting the Input Current by Limiting the Charger Current Input Current Controlled by Input Voltage Auxiliary Contacts Multi-unit configurations Accessories RCC-02 RCC-03Indicated alarm Comment ControlMain on/off control Display and control partsCheck the cause of this excess voltage. The equipment will EC declaration of conformity Maintenance of the installationProduct recycling Comments of annexes’ figures Example of installation in a vehicle AC part Installation example in a boat, with isolation transformerExample of a hybrid installation Example of parallel connection of 2 or 3 XtendersFigure elements DC part Elem Description CommentFigure elements AC part Elements of connexion cabinet a Control and display parts for the Xtender b Type plate elements bStuder Innotec Xtender Table of standard configurations Studer Innotec Xtender Technical data Model XTH 3000-12 XTH 5000-24 XTH 6000-48 XTH