Studer Innotec HPC5048, HPC2512, HPC7048, HPC4024 user manual Remote Control, Temperature sensor

Page 19
Dry contact only
max.
Remote control
60V/0,5A
COMPACT
1 2 3 4
ON/OFF ! -batt!
Remote control
(Change status)
AUXILIARY CONTACT (Program)
ON/OFF
Contact manual
OFF
Contact active
10 5 Ch Inv arg ert er er
Battery Low/High
Program
20 10
Overload
30 20
EQUALIZE
Over Temp.
60 80
50 60
40 40
SOLAR CHARGE
RESET
ALARM (Select)
70 100
CHARGER
INVERTER
100 160
90 160
80 130
AC OUT
AC IN
A %
TRANSFER
RCC-01
INVERTER - CHARGER
CO M P A CT
HP-COMPACT

STUDER INNOTEC

4.9The Remote Control

As an option, a Remote Con-

trol can be connected to the HP-COMPACT. All ope-

rating controls and displays except from level adjustment are available on the Remote Control. The Remote Control is supplied with a 20m long cable. It can as long as 40m. The Remote Control is sui- table for surface mounting on

the wall or on to a switch board. It is fixed with 4 screws. The HP-COMPACT can also be programmed

with the Remote Control. The Programming is descry- bed in the section „Program- ming“.

The output power and the charging currents are dis- played on the Remote Control. In the Remote Control there is an additional Alarm Contact and a built-in Control Input. These two functions are avai- lable through Tip-jack RJ11/4 for use. This Auxiliary Contact is Front / Work Contact (max. 0.5A!), which is independent from the Auxiliary Contact of the HP-COMPACT. This con- tact is active in case of an alarm of the HP-COMPACT.

The Control Input is connected in parallel to the ON/OFF- push button. The HP-COMPACT can be switched on or off through this input with an impulse button or an impulse contact.

Order Number for Remote Control: RCC-01

Dimensions: H x B x T / 111.5 x 136.5 x 25mm

Caution: No external voltage should be connected to this Input Control.

4.10 The Temperature sensor

Operating voltage of lead-acid batteries change depends on the temperature. To correct the operating voltages accord- ing to the actual temperatures, a temperature sensor can be connected to the HP-COMPACT.

The compensation through the sensor is –3mV/°C/Cell. Order Number: CT-35

Dimensions: H x B x T / 58 x 51.5 x 22mm

User manual

HP-COMPACT V3.0 E

19

Image 19
Contents User and installer Manual Summary Operating instructions Quality and WarrantyWarranty Disclaimer General InformationSpecial precautions PrecautionsIntroduction Battery connecting Battery chargerRemote control Remote control for Power SharingConnection in parallel and in serie Mounting and installingInstallation place Connection in serieProtection cover of the terminals connections General instructions on connectingFixing ConnectionsCabling BatteryConnection to battery Pre-installation settingsConnection to the 230Vac Input AC Input Connection to Remote controlConnection to Temperature Sensor Temp Connection to the 230Vac-consumer appliances AC OutputCharger Inverter ControlDisplay and control parameters Turning Knobs Push buttonsInverter Overheating Over Temp Battery ConditionCharge detection system „Standby OverloadEqualization charging Cycle of chargeCharging current Input current repartition Power sharingSet the transfer voltage threshold Transfer systemDelayed mode of the Transfer System Fast UPS- Mode for the Transfer SwitchMultifunctional Contact Temperature sensor Remote ControlTable of voltage and timing threshold Battery voltageProgramming Auxiliary contactPrinciple Set the voltage and timing thresholdExample start of a genset with the HP-COMPACT Disabling some of the HP-COMPACT functions Power cut of the second priority loadsDiagram of the different modes Manual operating of Auxiliary ContactEC Compliance Installation MaintenanceHPC2512 HPC4024 HPC5048 HPC7048 Technical Data