Skil 5380, 5480, 5385, 5485 manual Trouble Shooting

Page 14

SM 1619X05344 03-10:SM 1619X05344 03-10 3/10/10 3:06 PM Page 14

Trouble Shooting

!WARNING

PROBLEM

Read instruction manual first! Remove plug from the power source before making adjustments or assembling the blade.

TROUBLE: SAW WILL NOT START

1.Power cord is not plugged in.

2.Power source fuse or circuit breaker tripped.

3.Cord damaged.

4.Burned out switch.

5.Trigger does not turn tool on.

REMEDy

1.

Plug saw in.

 

2.

Replace fuse or reset tripped circuit breaker.

 

3.

Inspect cord for damage. If damaged, have cord replaced by an Authorized Skil

 

Service Center or Service Station.

 

4.

Have switch replaced by an Authorized Skil Service Center or Service Station.

 

5. Disengage Safety Switch as described on page 9

 

TROUBLE: BLADE DOES NOT COME UP TO SPEED

PROBLEM

1.

Extension cord too light or too long.

 

2.

Low house voltage.

REMEDy

1.

Replace with adequate cord.

 

2.

Contact your electric company.

 

TROUBLE: EXCESSIVE VIBRATION

PROBLEM

1.

Blade out of balance.

 

2.

Workpiece not clamped or supported properly.

REMEDy

1.

Discard Blade and use different blade.

 

2. Clamp or support workpiece as shown on pages 9 and 11.

 

TROUBLE: CANNOT MAKE SQUARE CUT WHEN CROSSCUTTING

PROBLEM

1.

Foot not adjusted properly.

REMEDy

1.

See “Operating Instructions” section, “Bevel Adjustment” (page 9), “Line Guide”

 

(page 10, “Cutting Large Sheets (page 11) and “Rip Cuts” (page 12).

TROUBLE: CUT BINDS, BURNS, STALLS MOTOR WHEN RIPPING PROBLEM 1. Dull blade with improper tooth set.

2.Warped board.

3.Blade binds.

4.Improper workpiece support.

REMEDy 1. Discard blade and use a different blade.

2.Make sure concave or hollow side is facing “DOWN” feed slowly, see (page 11).

3.Assemble blade and tighten Vari-Torque clutch per “Assembly Instructions”, see (page 8)

4.Clamp or support workpiece as shown on pages 9 and 11.

TROUBLE: BLADE SLIPPING

PROBLEM 1. Tool does not cut workpiece.

REMEDy 1. Assemble blade and tighten Vari-Torque clutch per “Assembly Instructions”, see (page 8)

-14-

Image 14
Contents Ver la página Leer antes de usarSee Electrical safety General Power Tool Safety WarningsWork area safety Personal safetyCutting procedures Safety Rules for Circular SawsService Causes and operator prevention Kickback Kickback and related warningsLower guard function VARI-TORQUE ClutchAdditional Safety Warnings Symbols Symbol Name Designation/ExplanationUpper Guard Functional Description and SpecificationsPower Indicator Light Assembly Operating Instructions Switch General CutsPlunge Cuts Lower Guard Lift Lever Foot Cutting Large SheetsMaintenance CleaningAccessories Trouble Shooting Sécurité du lieu de travail Sécurité électriqueEntretien Consignes de sécurité pour scies circulairesUtilisation et entretien des outils Électroportatifs Embrayage VARI-TORQUE Problèmes associésFonction du garde inférieur Avertissements supplémentaires concernant la sécurité Le plomb provenant des peintures à base de plombSymboles Symbole Nom Désignation/ExplicationPoignee Auxiliaire Secteur Gradué DE Biseau Description fonctionnelle et spécificationsScies circulaires Biseau SemelleAssemblage Verification DE L’ANGLE DE Coupe Consignes de fonctionnementReglage DE LA Profondeur DE Coupe Interrupteur Guide D’ALIGNEMENTCoupe Coupes RegulieresMauvaise Coupes EN GuichetLa lame ManièreEntretien NettoyageAccessoires Guide de diagnostic Seguridad personal Seguridad del área de trabajoSeguridad eléctrica Servicio de ajustes y reparaciones Normas de seguridad para sierras circularesMecánicas Procedimientos de corteEmbrague DE PAR Motor Variable El retroceso y advertencias relacionadasEl operador Advertencias de seguridad adicionales Función del protector inferiorSímbolos Símbolo Nombre Designación/explicaciónModelo 5380 Capacidades máximas Descripción funcional y especificacionesSierras circulares Mango Auxiliar Cuadrante DE Inclinacion CalibradoPerno DE LA Hoja EnsamblajeMuelle DEL Protector Inferior Protector SuperiorInstrucciones de funcionamiento Guia DE Interruptor Guia DE LineaCorte Cortes GeneralesIncorrecto Cortes POR PenetraciónSacar Limpieza MantenimientoServicio Accesorios CapacidadAvería LA Hoja no Alcanza Toda SU Velocidad Resolución de problemasAvería LA Sierra no Arranca Avería Vibración ExcesivaSM 1619X05344 03-10SM 1619X05344 03-10 3/10/10 306 PM Remarques Notas SM 1619X05344 03-10SM 1619X05344 03-10 3/10/10 306 PM