Skil 2487, 2587, 2887 manual Charging Battery Pack Fast Charger, Important Charging Notes

Page 11

SM 1619X00347 11-04 11/9/04 10:43 AM Page 11

CHARGING BATTERY PACK (FAST CHARGER)

Plug charger cord into your standard power outlet, then slide the battery pack into charger (Fig. 7).

The charger’s green indicator will begin to “BLINK”. This indicates that the battery is receiving a fast charge. Fast-charging will automatically stop when the battery pack is fully charged.

When the indicator light stops “BLINKING” (and becomes a steady green light) fast charging is complete.

When you begin the charging process of the battery pack, a steady green light could also mean the battery pack is too hot or too cold.

The purpose of the light is to indicate that the battery pack is fast-charging. It does not indicate the exact point of full charge. The light will stop blinking in less time if the battery pack was not completely discharged.

When the battery pack is fully charged, unplug the charger (unless you're charging another battery pack) and slip the battery pack back into the tool handle.

FIG. 7

CHARGER

 

 

 

 

 

 

 

 

 

 

INDICATOR

BATTERY PACK

LIGHT

 

 

 

 

IMPORTANT CHARGING NOTES

1.The battery pack accepts only about 80% of its maximum capacity with its first few charge cycles. However, after the first few charge cycles, the battery will charge to full capacity.

2.The charger was designed to fast charge the battery only when the battery temperature is between 40˚F (4˚C) and 105˚F (41˚C).

3.A substantial drop in operating time per charge may mean that the battery pack is nearing the end of its life and should be replaced.

4.If you anticipate long periods (i.e. a month or more) of non-use of your tool, it is best to run your tool down until it is fully discharged before storing your battery pack. After a long period of storage, the capacity at first recharge

will be lower. Normal capacity will be restored in two or three charge/discharge cycles. Remember to unplug charger during storage period.

5.If battery does not charge properly:

a.Check for voltage at outlet by plugging in some other electrical device.

b.Check to see if outlet is connected to a light switch which turns power “off” when lights are turned off.

c.Check battery pack terminals for dirt. Clean with cotton swab if necessary.

d.If you still do not get proper charging, take or send tool, battery pack and charger to your local Skil Service Center.

Note: Use of charger’s or battery packs not sold by Skil will void the warranty.

-11-

Image 11
Contents Voir Ver página For English Parlez-vous français?See Work Area General Safety Rules For All Battery Operated ToolsElectrical Safety Personal SafetyService Safety Rules for Cordless Drills/DriversLoss of control and kickback Battery/ChargerNICKEL-CADMIUM Batteries Battery CareBattery Disposal Nails, screws, keys, etc. Fire or injury may resultSymbols Tool Functional Description and SpecificationsBattery pack Cordless Drills/DriversOperating Instructions Drill BIT Storage Compartment and Quick Reference Gauge Installing ChuckInserting Bits Removing ChuckStud finders can detect ! Warning other objects besides Releasing and Inserting Battery PackCharging Battery Pack Standard Charger Flash . To correct, simply restart the circuitImportant Charging Notes Charging Battery Pack Fast ChargerMounting Charger to Vertical Surface Mounting ChargerOperating Tips Cleaning MaintenanceTool’s AccessoriesSécurité des personnes Consignes générales de sécurité Pour tous les outils à pileAire de travail Utilisation et entretien des outils Sécurité électriqueNe faites pas fonctionner la perceuse en la portant Consignes de sécurité pour perceuses/tournevis sans cordonRéparation Le plomb provenant des peintures à base de plomb Chargeur de pilePiles NICKEL-HYDRURE DE Métal Entretien des pilesMise au rebut des piles Piles NICKEL-CADMIUMSymboles Outil Description fonctionnelle et spécificationsPerceuses/tournevis sans cordon NON Disponible SUR Tous LES ModèlesConsignes de fonctionnement Calibre DE Référence Rapide Insertion DES ForetsRetrait DU Mandrin Pose DU MandrinDépose ET Repose DU BLOC-PILES Le milieu entre ces deux repères indique l’axe du poteauRemarques Importantes Concernant LA Charge Chargement DU BLOC-PILES Chargeur RapideSignifier que le bloc-pile est trop chaud ou trop froid Enlevez le bloc-piles du chargeur avant de fixer ce dernier Montage du chargeurMontage DU Chargeur À UNE Surface Verticale Consignes de fonctionnement Nettoyage Entretien= équipement standard = accessoire en option AccessoiresUtilización y cuidado de las herramientas Area de trabajoSeguridad eléctrica Seguridad personalServicio Batería/cargador Baterías DE NIQUEL-HIDRURO Metalico Cuidado de las bateríasEliminación de las baterías Baterías DE NIQUEL-CADMIODe Ni-Cd SímbolosCon aislamiento doble Capacidades máximas Descripción funcional y especificacionesTaladros/destornilladores sin cordón HerramientaInstrucciones de funcionamiento Localizador DE Postes DE Pared Colocacion DE LAS BrocasDesmontaje DEL Mandril Instalacion DEL MandrilCarga DEL Paquete DE Baterías Cargador Estándar CircuitoNotas Importantes Para Cargar Carga DEL Paquete DE Baterías Cargador RápidoMontaje DEL Cargador EN UNA Superficie Vertical Montaje del cargadorBrocas Para Taladro Consejos de funcionamientoTaladrado CON Velocidad Variable Sujecion CON TornillosLimpieza Mantenimiento= equipo estándar = accesorios opcionales AccesoriosSM 1619X00347 11-04 11/9/04 1043 AM