Skil 2466 2566 2866 manual Maintenance, Cleaning

Page 14

SM 1619X00551 11-04 11/29/04 11:46 PM Page 14

RUNNING NUTS AND BOLTS

Variable speed control must be used with caution for driving nuts and bolts with socket set attachments. The technique is to start slowly, increasing speed as the nut or bolt runs

down. Set the nut or bolt snugly by slowing the drill to a stop. If this procedure is not followed, the tool will have a tendency to torque or twist in your hands when the nut or bolt seats

Maintenance

Service

!WARNING NO USER SERVICEABLE PARTS INSIDE. Preventive

maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recom- mend that all tool service be performed by a Skil Factory Service Center or Authorized Skil Service Station. SERVICEMEN: Disconnect tool and/or charger from power source before servicing.

BATTERÍES

Be alert for battery packs that are nearing their end of life. If you notice decreased tool performance or significantly shorter running time between charges then it is time to replace the battery pack. Failure to do so can cause the tool to operate improperly or damage the charger.

Long term battery storage should be in the discharged state. Battery packs last longer and re-charge better when they are stored discharged. Remember to fully re- charge battery packs before using after prolonged storage.

TOOL LUBRICATION

Your Skil tool has been properly lubricated and is ready for use.

D.C. MOTORS

The motor in your tool has been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend it be examined every six months. Only a genuine Skil replacement motor specially designed for your tool should be used.

Cleaning

!WARNING To avoid accidents, always disconnect the tool and/or

charger from the power supply before cleaning. The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through opening.

Certain cleaning agents ! CAUTION and solvents damage

plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

-14-

Image 14
Contents Voir Ver página For English Parlez-vous français?See Electrical safety General Safety RulesWork area safety Personal safetyService Power tool use and careBattery tool use and care Power tools are dangerous in the hands of untrained usersLead from lead-based paints Safety Rules for Cordless Drills/DriversLoss of control and kickback Explode Battery/ChargerBattery Care Battery Disposal NICKEL-CADMIUM BatteriesSymbols Functional Description and Specifications Cordless Drills/DriversOperating Instructions Drill BIT Storage Compartment and Quick Reference Gauge Battery Charged Condition IndicatorDrill BIT and Screw Storage Compartment Stud FinderCharging Battery Pack 3 Hour Charger Fastening with Screws Operating TipsImportant Charging Notes Drilling with Variable SpeedDrilling Wood Wire BrushesDrill Bits Drilling MetalMaintenance CleaningAccessories Extension CordsSécurité électrique Consignes générales de sécuritéSécurité du lieu de travail Sécurité personnelleEntretien Utilisation et entretien des outils ÉlectroportatifsUtilisation et entretien des outils à piles Le plomb provenant des peintures à base de plomb Consignes de sécurité pour perceuses/tournevis sans cordonNe faites pas fonctionner la perceuse en la portant Chargeur de pile Entretien des pilesPiles NICKEL-CADMIUM Mise au rebut des pilesNe tentez pas de Symboles NON Disponible SUR Tous LES Modèles Description fonctionnelle et spécificationsPerceuses/tournevis sans cordon OutilConsignes de fonctionnement Localisateur DE Poteaux Témoin D’ÉTAT DE Charge DE LA PileCompartiment DE Rangement DES Embouts ET DES VIS Localisateur de poteauxDéfaut. Pour le corriger, il suffit de refermer le circuit Charge DU BLOC-PILE Chargeur DE 3 HeureConsignes de fonctionnement Perçage DES Métaux ForetsPerçage DU Bois Perçage DE LA MaçonnerieEntretien NettoyageAccessoires Cordons de rallongeSeguridad eléctrica Normas generales de seguridadSeguridad del área de trabajo Seguridad personalServicio de ajustes y reparaciones Mordazas sobre la broca y se aumenta la pérdida de control Batería/cargador Cuidado de las bateríasEliminación de las baterías Baterías DE NIQUEL-CADMIODe Ni-Cd SímbolosCon aislamiento doble Descripción funcional y especificaciones Taladros/destornilladores sin cordónInstrucciones de funcionamiento Brocas Taladradoras Y Tornillos Localizador DE Postes DE ParedCarga DEL Paquete DE Baterías Cargador DE 3 Hora Horas para cargarse completamenteSujecion CON Tornillos Consejos de funcionamientoNotas Importantes Para Cargar Taladrado DE Metal Brocas Para TaladroTaladrado DE Madera Taladrado DE MamposteriaLimpieza MantenimientoServicio Cordones de extensión AccesoriosSM 1619X00551 11-04 11/29/04 1146 PM