Bryant 619E manual Outdoor unit. Sensible heat capacity shall not be less than

Page 31

ENGINEER'S SPECIFICATION GUIDE Ð OUTDOOR UNITS (Models 538A, 538C, 538D, and 538S )

GENERAL: Furnish and install a Model 538A, 538C, 538D, or 538S air-to-air outdoor unit in combination with a fan coil unit in the location and manner shown on the plan drawings. The unit shall be designed and tested for use with Refrigerant R-22 and shall be equipped with refrigerant line ®ttings which permit sweat or ¯are connections.

Nominal system electrical characteristics shall be v,

single phase, 60 Hz. Each unit shall be capable of satisfactory

operation within voltage range of

 

 

v to

 

 

v.

MAXIMUM DIMENSIONS: Outdoor unit Ð width

 

 

in.,

depth

 

in., height

 

 

inches.

 

 

COOLING CAPACITY: Total system cooling capacity shall not

be less than

 

 

Btuh with indoor air quantity of

 

cfm at

 

 

 

F wet bulb temperature of air entering

outdoor unit. Sensible heat capacity shall not be less than

 

Btuh with

 

F dry bulb temperature. Compres-

sor power input shall be

 

 

v or less at these conditions.

HEATING CAPACITY (Heat Pump Systems Only): Total heating

capacity shall be

 

 

Btuh or greater (integrated rating)

when rated at

 

 

 

F dry-bulb outdoor ambient with cfm

and

 

 

F entering (heating) coil. The equipment must

have a minimum HSPF of

 

 

. Compressor shall be ca-

pable of operation in heating duty down to −20 F outdoor am- bient air temperature (with accessory low-ambient kit). Unit shall be capable of simultaneous heating duty and defrost cycle operation.

OUTDOOR SECTION: The coil shall be constructed of alumi- num plate ®ns mechanically bonded to copper tubing with all

joints brazed. Coil shall be

 

rows deep with a nominal

®n spacing of

®ns per in., and shall have a face area of

not less than

 

square ft.

 

Outdoor unit shall contain a fully hermetic compressor with a crankcase heater (non-scroll units), oil system, operating oil charge, internal motor protection, and spring isolation. Outdoor fans shall be direct-drive propeller type, shall discharge air hori- zontally, shall be totally enclosed, and shall have permanently lubricated sleeve bearings.

CONTROL CIRCUIT: Controls and protective devices shall in- clude time-delay restart, automatic restart on power failure, 3-pole contactors (3 phase units), safety lockout if any safety is open, high-pressure and loss-of-pressure switches, automatic outdoor-fan motor protection, start capacitor and relay (single- phase units without scroll compressors), system diagnostics and high condensing temperature protection , compressor mo- tor current and temperature overload protection, high pressure relief, and outdoor fan failure protection. A 24-v transformer shall be factory installed and wired on outdoor units for external control circuit (size 018 and 024 only).

APPROVALS: Unit shall be constructed in accordance with ASHRAE 15 (latest revision), NEC, and CSA. Unit shall carry the UL listing label.

FIELD-INSTALLED ACCESSORIES: Low-ambient kit (538A, 538C, 538D), liquid solenoid valve, wall mount kit, crankcase heater (reciprocating-compressor units only) and winter start kit (538C, 538S).

31

Image 31
Contents Description Standard System FeaturesAir Conditioning 538A 538S 048 ShownContents FIELD-INSTALLED Accessory Description and Usage619B,D Standard Features and FIELD-INSTALLED AccessoriesModel Description Hspf System CapacitiesSeer Unit Specifications Ð 538A and 538C Condensing UnitsUnit 538D Specifications Ð 538D Heat Pump UnitsUnit 619E Specifications Ð 538S Condensing UnitsSpecifications Ð 619E FAN Coil Units Unit 538S538 009 55.0 25.0 012 62.0 28.1 60.7 27.5 66.5 30.2 Unit WeightUnit Minimum Mounting PAD DimensionsUnit Operating Unit Operating Weight 538S Ft-in Dimensional DRAWING, Base Unit Ð 538S Condensing UnitsFt-in 024 048619E 009 Dimensional DRAWING, Base Unit Ð 619E009,012 FAN Coil Units619E Dimensional DRAWING, Base Unit Ð 619E018,024 FAN Coil UnitsHeat Pump Units Electrical Data Condensing UnitsMULTI-SPLIT Condensing Units Operating Voltage FAN Unit Electrical DataFAN Coil Units IndoorCooling-Only System Shown Cooling Only System Shown Condition ALL Units Application DataOutdoor Units ConditionFAN Coil Unit Equivalent Below Above Condensing Application DataMaximum Line Lengths Maximum Lift ÐHeat Pump System Piston Guide and Refrigerant Charges Fitting Loss in Equivalent FT for ElbowsChattleff Common Piston Sizes Cooling only System Piston Guide and Refrigerant ChargesIndoor Unit Above Outdoor Unit Change in Indoor Unit Piston Size For ElevationHorizontal Conguration Outdoor Unit Above Indoor UnitUnit FAN Speed AIR Throw DataCondensing Unit Sound Ratings FAN Coil High Speed ApproximateCompressor Relay ChartThermistor Equivalence Typical Wiring Schematic Ð 538A018,024 COOLING-ONLY SystemTemperatureResistance 500 11,400 32,500 Compressor K13Outdoor Fan K2 Compressor K1 Temperature Resistance 500 11,400 32,500 Typical Wiring Schematic Ð 538D018,024 Heat Pump SystemOperating Sequence Operating Sequence Electronic Control Defrost Regions Map Outdoor unit. Sensible heat capacity shall not be less than Bryant Day & Night Payne