Grizzly G0664 owner manual Setup Safety, Items Needed for, Unpacking

Page 12

SECTION 3: SETUP

Setup Safety

This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine!

Wear safety glasses dur- ing the entire setup pro- cess!

The Model G0664 is an extremely heavy machine. Serious per- sonal injury may occur if safe moving methods are not followed. To be safe, you will need assistance and power equipment when moving the ship- ping crate and remov- ing the machine from the crate.

CUTTING HAZARD!

Blades are sharp! Put on heavy leather gloves when handling a blade or making adjustments near a blade or cutter!

	Items Needed for
	Setup
The following items are needed to complete the
setup process, but are not included with your
machine:
Description		Qty
•	Assistant	1
• Safety Glasses (for each person)		1 Pair
•	Mounting Hardware (optional)	As Needed
•	Power Lifting Equipment
	(Rated for at least 1200 lbs.)	1
• Lifting Straps and Hooks
	(Rated for at least 1200 lbs.)	As Needed
	Unpacking

The Model G0664 was carefully packed when it left our warehouse. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advise.

Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi- tion of your shipment, you should inventory the contents.

-12-	G0664 Heavy Duty Metal-Cutting Bandsaw

Image 12

Contents Model G0664 Heavy Duty Metal Cutting Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Foreword Functional OverviewContact Info Identification Machine Data Sheet Coolant Pump Motor !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions for Bandsaws Hearing Protection & HazardsCircuit Requirements 220V OperationSetup Setup SafetySetup Items Needed forInventory Machine Inventory Figure QtyHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadMoving & Placing To move the machineUsing Machine Mounts Mounting to Shop FloorBolting to Concrete Floors To install the leveling feet Leveling FeetMachine Leveling Proceed to Leveling MachineRoller Table Assembly To assemble the roller tablesRequired Adjustments Coolant Reservoir Cover/Catch TrayTest Run 34/0 UttonRecommended Adjustments Factory adjustments that should be verifiedOperation Safety OperationsBasic Controls Blade Guide Lock Handle Locks/ReleasesControl Panel Blade Downfeed KnobCutting Angle To set the cutting angle between 0Coolant Catch Tray To position the blade guideTo install the workstop WorkstopViseTo use the vise #/--%.$%$ Cutting Fluid System To use the cutting fluid systemCutting Fluid Tips Blade Selection Blade TerminologyBlade Pitch TPI To select the correct blade pitchSetting Feed Rate Blade LengthBlade Width To set the feed rateBlade Speed Material speed table G0664 Heavy Duty Metal-Cutting BandsawChip Inspection Chart AdditionalAppearance ActionsBlade Tensioning Blade Care Break-InBlade Care Blade Break-InBlade Breakage Workpiece InspectionMost common causes of blade breakage are Tanks, Cylinders, Containers, Valves, EtcOperation Tips Accessories H5405-LenoxLube TubeG5562-SLIPIT1 Qt. Gel G5563-SLIPIT12 oz Spray T20448T20452 T20501 T20456 H0736Maintenance CleaningSchedule LubricationHydraulic System Checking Hydraulic FluidChanging Hydraulic Fluid Figure Service TroubleshootingMotor & Electrical Or Blade Speed on Page 34 and adjust as Bandsaw OperationsHydraulic System Troubleshooting Blade Change Blade Guides To adjust/replace the wheel brush Wheel BrushSquaring Blade To square the bladeTo adjust the swivel stops Swivel StopsLimit Switches To adjust the feed stop boltTo set the upper travel auto stop and lower limit switch Feed StopWiring Electrical Safety InstructionsWiring Overview 220 VACControl Box Wiring Diagram Components Wiring Diagram Coolant pump motorControl panel wiring Control Box Electrical ComponentsHydraulics See FiguresHydraulic Components SolenoidsParts Main Parts List DescriptionRoller Stand Parts Breakdown & List Base BreakdownBase Breakdown Labels Breakdown and List 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%