Grizzly Model G1022proz instruction manual Main Features

Page 15

shaped channel along the edge of wood stock.

Splitter: Metal plate attached to the back of the blade guard that maintains the kerf opening in the wood when performing a cutting operation.

Standard Kerf: 1Ú8" gap made with a standard blade.

Straightedge: A tool used to check the flatness, parallelness, or consistency of a surface(s).

Main Features

Set up and operation instructions will be easier to understand if you become familiar with the loca- tion and names of the basic features.

Match up the feature list below with the letters in Figure 7 to identify the table saw feature loca- tions.

Thru-Sawing:A sawing operation where the wood stock thickness is completely sawn through. Proper blade height usually allows 1Ú4" of the top of the blade to extend above the wood stock.

Thin Kerf: 3Ú32" gap made with a thin kerf blade.

Rip Cut: A cut made along the grain of the wood.

Sacrificial Fence: A piece of wood attached to the face of the rip fence that is designed to extend the fence face away from the metal por- tion of the fence. Used primarily when making rabbet cuts with a dado blade.

I

A

B

C

H

G

F

E

D

Figure 7. The front of the table saw.

(Model SM Shown)

A. Extension Wing

B. On/Off Switch

C. Blade Angle Handwheel

D.Stand

E.Blade Height Handwheel

F.Rip Fence Rails

G.Rip Fence

H.Blade Guard/Splitter Assembly

I.Miter Gauge

 

 

 

 

 

 

 

 

 

 

 

 

G1022 Series Table Saws

-13-

Image 15
Contents G1022ZFX G1022SM G1022Z G1022ZFPage Table Of Contents Safety Instructions For Power Tools Safety25ft 50ft 100ft AMP RatingAdditional Safety Instructions For Table Saws Following can help minimize kickbacks Avoiding Kickback Safety AccessoriesZero Clearance Table Inserts Push PaddlesFeatherboards Commentary IntroductionG1022 Series Table Saws Model ZF Circuit Requirements110V Operation Models SM & ZModels ZFX, PROZ, & Prozx 220V OperationExtension Cord GroundingTerms and Definitions Machine FeaturesMain Features Unpacking Piece Inventory SET UPMotor with Pulley Hardware Contents Bolt Hardware Recognition ChartWorking Clearance Clean UpSite Considerations Floor LoadBeginning Assembly Stand Assembly Models ZF, ZFX, PRO, & Prozx only Stand completely assembledHandwheels All ModelsTo mount the handwheels Motor Checking V-belt alignment Models ZF, ZFX, PROZ, & Prozx SwitchExtension Wings To mount the rails Models SM & Z To install and adjust the Model SM fenceFence Rails FenceAdjust measurement pointer G1022 Series Table Saws Attaching a sacrificial fence To install and adjust the Model Z fenceAttaching a sacrificial fence G1022 Series Table Saws Changing saw blade G1022 Series Table Saws BladeBlade Guard Installing blade guardProper Alignment Added Washers Table Insert Adjusting table insert components G1022 Series Table SawsMiter Gauge Initial Step Models ZF, ZFX, PROZ, & ProzxNext steps for all models Start Up Recommended Adjustments Recommended adjustment checklistStarting the machine Blade Selection OperationsVarious saw tooth cutting profiles G1022 Series Table Saws Cross-cut operation G1022 Series Table Saws CrosscuttingRipping operation RippingSingle-blade dado cut Dado CuttingIf the cut is satisfactory, repeat with your fin- ish stock Sacrificial fence G1022 Series Table Saws Rabbet CuttingCutting rabbets with the dado blade Disconnect the machine from the powerCutting rabbets with the standard blade Rabbet cutting G1022 Series Table Saws General MaintenanceLubrication BeltLubricate the areas indicated below every 12 months Date Approximate Hours Of Use Maintenance Performed Blade Parallelism Service AdjustmentsTo shift the trunnion Shim placement G1022 Series Table SawsTo shim the trunnion 45˚ & 90˚ Stops Closure SM and Z Wiring Diagram ZF, ZFX, Proz & Prozx Wiring Diagram Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Models G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx Parts List Switch L-BRACKET Symptom Possible Cause Corrective Action Troubleshooting GuidePush Stick G1022 Series Table Saws G1022 Series Table Saws Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA Page Call Today For a Free Full Color Catalog