Grizzly Model G1022proz Clean Up, Site Considerations, Floor Load, Working Clearance, Lighting

Page 20

Clean Up

The unpainted surfaces are coated with a waxy oil to protect them from corrosion during ship- ment. Remove this waxy oil with a solvent clean- er or citrus-based degreaser such as GrizzlyÕs G7895 Degreaser. To clean thoroughly, some parts may need to be removed. The machine will operate best when the waxy oil is removed from all moving and sliding parts. Chlorine-based cleaners and solvents will dam- age the painted surfaces of the machine. Follow the manufacturerÕs instructions when using any type of cleaning product.

Gasoline or petroleum products used to clean the machinery could explode causing serious personal injury. DO NOT use gasoline or petrole- um products to clean the machinery.

Smoking near solvents could ignite an explosion or fire causing serious per- sonal injury. Do not smoke while using solvents.

Lack of ventilation while using solvents could cause serious personal health risks, fire, or environmental hazards. Always work in a well ventilated areas to pre- vent the accumulation of dangerous fumes. Supply the work area with a constant supply of fresh air using a fan.

-18-

Site Considerations

Floor Load

The Model G1022 Series Table Saws are a heavy load with a medium footprint. Most commercial or home shop floors should be sufficient to carry the weight of the machine. Reinforce the floor if you question its ability to support the weight.

Working Clearance

Working clearances can be thought of as the dis- tances between machines and obstacles that allow safe operation of every machine without lim- itation. Consider existing and anticipated machine needs, size of material to be processed through each machine, and space for auxiliary stands or work tables. Also, consider the relative position of each machine to one another for efficient materi- al handling. Be sure to allow yourself sufficient room to safely run your machines in any foresee- able operation and keep dust collection hoses off the floor and out of the way.

Lighting

Lighting should be bright enough to eliminate shadows and prevent eye strain. Electrical circuits should be dedicated or large enough to handle combined motor amp loads. Be sure to follow local electrical codes for proper installation of new lighting or circuits.

Unsupervised children and visitors entering a shop could receive seri- ous personal injury. Ensure child and visitors safety by keeping all entrances to the shop locked at all times. DO NOT allow unsupervised children or visitors in the shop at any time.

G1022 Series Contractor Saws

Page 19 Page 21
Image 20
Page 19 Page 21
Contents G1022SM G1022Z G1022ZF G1022ZFXPage Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating 25ft 50ft 100ftAdditional Safety Instructions For Table Saws Avoiding Kickback Safety Accessories Following can help minimize kickbacksFeatherboards Zero Clearance Table InsertsPush Paddles Introduction CommentaryG1022 Series Table Saws Circuit Requirements 110V OperationModels SM & Z Model ZF220V Operation Models ZFX, PROZ, & ProzxGrounding Extension CordMachine Features Terms and DefinitionsMain Features SET UP Unpacking Piece InventoryMotor with Pulley Hardware Contents Hardware Recognition Chart BoltClean Up Site ConsiderationsFloor Load Working ClearanceBeginning Assembly Stand Assembly Stand completely assembled Models ZF, ZFX, PRO, & Prozx onlyTo mount the handwheels HandwheelsAll Models Motor Checking V-belt alignment Switch Models ZF, ZFX, PROZ, & ProzxExtension Wings To install and adjust the Model SM fence Fence RailsFence To mount the rails Models SM & ZAdjust measurement pointer G1022 Series Table Saws To install and adjust the Model Z fence Attaching a sacrificial fenceAttaching a sacrificial fence G1022 Series Table Saws Blade Changing saw blade G1022 Series Table SawsInstalling blade guard Blade GuardProper Alignment Added Washers Adjusting table insert components G1022 Series Table Saws Table InsertNext steps for all models Miter GaugeInitial Step Models ZF, ZFX, PROZ, & Prozx Starting the machine Start Up Recommended AdjustmentsRecommended adjustment checklist Operations Blade SelectionVarious saw tooth cutting profiles G1022 Series Table Saws Crosscutting Cross-cut operation G1022 Series Table SawsRipping Ripping operationDado Cutting Single-blade dado cutIf the cut is satisfactory, repeat with your fin- ish stock Rabbet Cutting Sacrificial fence G1022 Series Table SawsDisconnect the machine from the power Cutting rabbets with the dado bladeCutting rabbets with the standard blade Rabbet cutting G1022 Series Table Saws Maintenance GeneralLubricate the areas indicated below every 12 months LubricationBelt Date Approximate Hours Of Use Maintenance Performed Service Adjustments Blade ParallelismShim placement G1022 Series Table Saws To shift the trunnionTo shim the trunnion 45˚ & 90˚ Stops Closure SM and Z Wiring Diagram ZF, ZFX, Proz & Prozx Wiring Diagram Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Models G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick G1022 Series Table Saws G1022 Series Table Saws Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA Page Call Today For a Free Full Color Catalog
Top Page Image Contents