Grizzly Model G1022proz instruction manual Checking V-belt alignment

Page 25

Motor Mount Bracket

Motor Mount Plate

Figure 18. Installing the motor mount bracket.

6.Line up the hole in the motor bracket with the hole in the motor mount plate and insert the motor pivot rod. Make sure the groove in the rod lines up with the setscrew in the mount bracket.

7.Tighten the setscrew.

8.Turn the arbor tilting handwheel until the arbor is set to 0¡.

9.Slide the motor assembly onto the linking bars through the holes in the motor bracket as shown in Figure 19.

10.Line up the setscrews with the grooves on the linking bars and tighten them.

Linking Bars

Figure 19. Attaching motor to linking bars.

G1022 Series Table Saws

11.Lift the motor up and slip the V-belt over the grooves in the pulleys. Slowly release the motor, allowing its weight to add tension to the V-Belt as shown in Figure 20.

!

Figure 20. Attaching the V-belt to the motor.

12.Place a straightedge across the arbor pulley and the motor pulley. The straightedge should run across both pulleys evenly as shown in Figure 21.

13.If the motor needs to be adjusted, loosen the mounting bolt tightened in Step 4.

14.Adjust the motor on its mount until the pul- leys are aligned, then tighten all the mount- ing bolts.

!

Figure 21. Checking V-belt alignment.

-23-

Image 25
Contents G1022ZFX G1022SM G1022Z G1022ZFPage Table Of Contents Safety Instructions For Power Tools Safety25ft 50ft 100ft AMP RatingAdditional Safety Instructions For Table Saws Following can help minimize kickbacks Avoiding Kickback Safety AccessoriesPush Paddles Zero Clearance Table InsertsFeatherboards Commentary IntroductionG1022 Series Table Saws 110V Operation Circuit RequirementsModels SM & Z Model ZFModels ZFX, PROZ, & Prozx 220V OperationExtension Cord GroundingTerms and Definitions Machine FeaturesMain Features Unpacking Piece Inventory SET UPMotor with Pulley Hardware Contents Bolt Hardware Recognition ChartSite Considerations Clean UpFloor Load Working ClearanceBeginning Assembly Stand Assembly Models ZF, ZFX, PRO, & Prozx only Stand completely assembledAll Models HandwheelsTo mount the handwheels Motor Checking V-belt alignment Models ZF, ZFX, PROZ, & Prozx SwitchExtension Wings Fence Rails To install and adjust the Model SM fenceFence To mount the rails Models SM & ZAdjust measurement pointer G1022 Series Table Saws Attaching a sacrificial fence To install and adjust the Model Z fenceAttaching a sacrificial fence G1022 Series Table Saws Changing saw blade G1022 Series Table Saws BladeBlade Guard Installing blade guardProper Alignment Added Washers Table Insert Adjusting table insert components G1022 Series Table SawsInitial Step Models ZF, ZFX, PROZ, & Prozx Miter GaugeNext steps for all models Recommended adjustment checklist Start Up Recommended AdjustmentsStarting the machine Blade Selection OperationsVarious saw tooth cutting profiles G1022 Series Table Saws Cross-cut operation G1022 Series Table Saws CrosscuttingRipping operation RippingSingle-blade dado cut Dado CuttingIf the cut is satisfactory, repeat with your fin- ish stock Sacrificial fence G1022 Series Table Saws Rabbet CuttingCutting rabbets with the dado blade Disconnect the machine from the powerCutting rabbets with the standard blade Rabbet cutting G1022 Series Table Saws General MaintenanceBelt LubricationLubricate the areas indicated below every 12 months Date Approximate Hours Of Use Maintenance Performed Blade Parallelism Service AdjustmentsTo shift the trunnion Shim placement G1022 Series Table SawsTo shim the trunnion 45˚ & 90˚ Stops Closure SM and Z Wiring Diagram ZF, ZFX, Proz & Prozx Wiring Diagram Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Models G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx Parts List Switch L-BRACKET Symptom Possible Cause Corrective Action Troubleshooting GuidePush Stick G1022 Series Table Saws G1022 Series Table Saws Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA Page Call Today For a Free Full Color Catalog