Grizzly Model G1022proz instruction manual 45˚ & 90˚ Stops

Page 54

45˚ & 90˚ Stops

The Model G1022 Series Table Saws are equipped with positive stops at 45¡ and 90¡. When properly adjusted, they provide precise and dependable guides for bevel adjustment.

Use caution and remain alert when working around the saw blade. Failure to follow this warning could result in serious personal injury or death.

To set the 45˚ & 90˚ stops:

1.Disconnect the machine from the power source!!

2.Raise the saw blade to its maximum height by turning the front handwheel clockwise.

3.Adjust the blade to the 90û position.

!

Figure 65. Checking blade angle to table.

5.With the square in place, inspect for gaps along the blade and square.

6.If a gap exists at either the top or the bottom of the square, loosen lock nut (A) and adjust- ment bolt (B) shown in Figure 66.

B A

C

D

Figure 66. 90¡ and 45¡ stop bolt adjustments.

7.Turn the handwheel until the blade and square are flush from top to bottom.

8.Snug the adjustment screw and tighten the lock nut.

9.Recheck the blade with the square to ensure the screw has not been over-tightened.

10.Using the side handwheel, adjust the blade bevel until you hit the 45¡ positive stop. Check the bevel with an adjustable square set to 45û.

11.If variations exist, loosen the lock nut (C) and adjust the stop bolt (D) (Figure 66) until your blade and square match.

12.Tighten the lock nut and recheck the bevel by adjusting the blade back to 90¡, then back to 45¡.

-52-

G1022 Series Table Saws

Image 54
Contents G1022SM G1022Z G1022ZF G1022ZFXPage Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating 25ft 50ft 100ftAdditional Safety Instructions For Table Saws Avoiding Kickback Safety Accessories Following can help minimize kickbacksZero Clearance Table Inserts Push PaddlesFeatherboards Introduction CommentaryG1022 Series Table Saws Models SM & Z Circuit Requirements110V Operation Model ZF220V Operation Models ZFX, PROZ, & ProzxGrounding Extension CordMachine Features Terms and DefinitionsMain Features SET UP Unpacking Piece InventoryMotor with Pulley Hardware Contents Hardware Recognition Chart BoltFloor Load Clean UpSite Considerations Working ClearanceBeginning Assembly Stand Assembly Stand completely assembled Models ZF, ZFX, PRO, & Prozx onlyHandwheels All ModelsTo mount the handwheels Motor Checking V-belt alignment Switch Models ZF, ZFX, PROZ, & ProzxExtension Wings Fence To install and adjust the Model SM fenceFence Rails To mount the rails Models SM & ZAdjust measurement pointer G1022 Series Table Saws To install and adjust the Model Z fence Attaching a sacrificial fenceAttaching a sacrificial fence G1022 Series Table Saws Blade Changing saw blade G1022 Series Table SawsInstalling blade guard Blade GuardProper Alignment Added Washers Adjusting table insert components G1022 Series Table Saws Table InsertMiter Gauge Initial Step Models ZF, ZFX, PROZ, & ProzxNext steps for all models Start Up Recommended Adjustments Recommended adjustment checklistStarting the machine Operations Blade SelectionVarious saw tooth cutting profiles G1022 Series Table Saws Crosscutting Cross-cut operation G1022 Series Table SawsRipping Ripping operationDado Cutting Single-blade dado cutIf the cut is satisfactory, repeat with your fin- ish stock Rabbet Cutting Sacrificial fence G1022 Series Table SawsDisconnect the machine from the power Cutting rabbets with the dado bladeCutting rabbets with the standard blade Rabbet cutting G1022 Series Table Saws Maintenance GeneralLubrication BeltLubricate the areas indicated below every 12 months Date Approximate Hours Of Use Maintenance Performed Service Adjustments Blade ParallelismShim placement G1022 Series Table Saws To shift the trunnionTo shim the trunnion 45˚ & 90˚ Stops Closure SM and Z Wiring Diagram ZF, ZFX, Proz & Prozx Wiring Diagram Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Models G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick G1022 Series Table Saws G1022 Series Table Saws Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA Page Call Today For a Free Full Color Catalog