Grizzly Model G1022proz instruction manual Table Of Contents

Page 3

	Table Of Contents
		PAGE
1.	SAFETY
	SAFETY RULES FOR ALL TOOLS	2-3
	ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWS	4
	AVOIDING KICKBACK	5
	SAFETY ACCESSORIES	5-6
2.	INTRODUCTION
	COMMENTARY	7-8
3.	CIRCUIT REQUIREMENTS
	110V OPERATION	9
	220V OPERATION	10
	GROUNDING	11
	EXTENSION CORD	11
4.	MACHINE FEATURES
	TERMS AND DEFINITIONS	12-13
5.	SET UP
	UNPACKING	14
	PIECE INVENTORY	14-15
	HARDWARE CONTENTS	16
	HARDWARE RECOGNITION CHART	17
	CLEAN UP	18
	SITE CONSIDERATIONS	18
	BEGINNING ASSEMBLY	19
	STAND ASSEMBLY	19-21
	HANDWHEELS	21
	MOTOR	22-24
	SWITCH	24
	EXTENSION WINGS	25
	FENCE RAILS	26
	FENCE	26-29
	BLADE	30
	BLADE GUARD	31-32
	TABLE INSERT	33
	MITER GAUGE	34
	START UP	35
	RECOMMENDED ADJUSTMENTS	35
6.	OPERATIONS
	BLADE SELECTION	36-37
	CROSSCUTTING	38
	RIPPING	39
	DADO CUTTING	40-42
	RABBET CUTTING	42-45

7.MAINTENANCE

	GENERAL	46
	LUBRICATION	47
	TABLE	47
	V-BELT	47
	MAINTENANCE LOG	48
8.	SERVICE ADJUSTMENTS
	BLADE PARALLELISM	49-51
	45û & 90û STOPS	52
9.	CLOSURE
	WIRING DIAGRAMS	54-55
	PART DRAWINGS & LISTS	56-73
	TROUBLESHOOTING	74
	PUSHSTICK LAYOUT	75

Image 3

Contents G1022ZFX G1022SM G1022Z G1022ZFPage Table Of Contents Safety Instructions For Power Tools Safety25ft 50ft 100ft AMP RatingAdditional Safety Instructions For Table Saws Following can help minimize kickbacks Avoiding Kickback Safety AccessoriesZero Clearance Table Inserts Push PaddlesFeatherboards Commentary IntroductionG1022 Series Table Saws Model ZF Circuit Requirements110V Operation Models SM & ZModels ZFX, PROZ, & Prozx 220V OperationExtension Cord GroundingTerms and Definitions Machine FeaturesMain Features Unpacking Piece Inventory SET UPMotor with Pulley Hardware Contents Bolt Hardware Recognition ChartWorking Clearance Clean UpSite Considerations Floor LoadBeginning Assembly Stand Assembly Models ZF, ZFX, PRO, & Prozx only Stand completely assembledHandwheels All ModelsTo mount the handwheels Motor Checking V-belt alignment Models ZF, ZFX, PROZ, & Prozx SwitchExtension Wings To mount the rails Models SM & Z To install and adjust the Model SM fenceFence Rails FenceAdjust measurement pointer G1022 Series Table Saws Attaching a sacrificial fence To install and adjust the Model Z fenceAttaching a sacrificial fence G1022 Series Table Saws Changing saw blade G1022 Series Table Saws BladeBlade Guard Installing blade guardProper Alignment Added Washers Table Insert Adjusting table insert components G1022 Series Table SawsMiter Gauge Initial Step Models ZF, ZFX, PROZ, & ProzxNext steps for all models Start Up Recommended Adjustments Recommended adjustment checklistStarting the machine Blade Selection OperationsVarious saw tooth cutting profiles G1022 Series Table Saws Cross-cut operation G1022 Series Table Saws CrosscuttingRipping operation RippingSingle-blade dado cut Dado CuttingIf the cut is satisfactory, repeat with your fin- ish stock Sacrificial fence G1022 Series Table Saws Rabbet CuttingCutting rabbets with the dado blade Disconnect the machine from the powerCutting rabbets with the standard blade Rabbet cutting G1022 Series Table Saws General MaintenanceLubrication BeltLubricate the areas indicated below every 12 months Date Approximate Hours Of Use Maintenance Performed Blade Parallelism Service AdjustmentsTo shift the trunnion Shim placement G1022 Series Table SawsTo shim the trunnion 45˚ & 90˚ Stops Closure SM and Z Wiring Diagram ZF, ZFX, Proz & Prozx Wiring Diagram Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Models G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx Parts List Switch L-BRACKET Symptom Possible Cause Corrective Action Troubleshooting GuidePush Stick G1022 Series Table Saws G1022 Series Table Saws Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA Page Call Today For a Free Full Color Catalog