Grizzly Model G1022proz Stand completely assembled, Models ZF, ZFX, PRO, & Prozx only

Page 22

Figure 10. Long upper and lower braces

attached to the stand legs.

3.Attach the short upper and lower side braces (2 each) to one of the assembled side pan- els using M8 - 1.25 x 16 carriage bolts, 8MM flat washers and M8-1.25 hex nuts as shown in Figure 11.

Figure 11. Short upper and lower braces attached to one of the stand assemblies.

4.Bolt the stand assemblies together using M8-1.25 x 16 carriage bolts, 8MM flat wash- ers and M8-1.25 hex nuts as shown in Figure 12.

Figure 12. Stand completely assembled.

Models ZF, ZFX, PRO, & PROZX only:

5.Align the bolt holes on the dust hood with the bolt holes on the dust hood adapter.

6.Secure the dust hood and the dust adapter together using 10-24 x 3Ú8" bolts, 10-24 nuts and 3Ú16" lock washers.

7.Turn the table saw body upside-down.

8.Place the dust hood assembly over the bot- tom of the table saw body with the dust hood flange pointed up.

-20-	G1022 Series Table Saws

Image 22

Contents G1022SM G1022Z G1022ZF G1022ZFXPage Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating 25ft 50ft 100ftAdditional Safety Instructions For Table Saws Avoiding Kickback Safety Accessories Following can help minimize kickbacksPush Paddles Zero Clearance Table InsertsFeatherboards Introduction CommentaryG1022 Series Table Saws Models SM & Z Circuit Requirements110V Operation Model ZF220V Operation Models ZFX, PROZ, & ProzxGrounding Extension CordMachine Features Terms and DefinitionsMain Features SET UP Unpacking Piece InventoryMotor with Pulley Hardware Contents Hardware Recognition Chart BoltFloor Load Clean UpSite Considerations Working ClearanceBeginning Assembly Stand Assembly Stand completely assembled Models ZF, ZFX, PRO, & Prozx onlyAll Models HandwheelsTo mount the handwheels Motor Checking V-belt alignment Switch Models ZF, ZFX, PROZ, & ProzxExtension Wings Fence To install and adjust the Model SM fenceFence Rails To mount the rails Models SM & ZAdjust measurement pointer G1022 Series Table Saws To install and adjust the Model Z fence Attaching a sacrificial fenceAttaching a sacrificial fence G1022 Series Table Saws Blade Changing saw blade G1022 Series Table SawsInstalling blade guard Blade GuardProper Alignment Added Washers Adjusting table insert components G1022 Series Table Saws Table InsertInitial Step Models ZF, ZFX, PROZ, & Prozx Miter GaugeNext steps for all models Recommended adjustment checklist Start Up Recommended AdjustmentsStarting the machine Operations Blade SelectionVarious saw tooth cutting profiles G1022 Series Table Saws Crosscutting Cross-cut operation G1022 Series Table SawsRipping Ripping operationDado Cutting Single-blade dado cutIf the cut is satisfactory, repeat with your fin- ish stock Rabbet Cutting Sacrificial fence G1022 Series Table SawsDisconnect the machine from the power Cutting rabbets with the dado bladeCutting rabbets with the standard blade Rabbet cutting G1022 Series Table Saws Maintenance GeneralBelt LubricationLubricate the areas indicated below every 12 months Date Approximate Hours Of Use Maintenance Performed Service Adjustments Blade ParallelismShim placement G1022 Series Table Saws To shift the trunnionTo shim the trunnion 45˚ & 90˚ Stops Closure SM and Z Wiring Diagram ZF, ZFX, Proz & Prozx Wiring Diagram Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Models G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick G1022 Series Table Saws G1022 Series Table Saws Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA Page Call Today For a Free Full Color Catalog