Grizzly Model G1022proz instruction manual AMP Rating, 25ft 50ft 100ft

Page 5

Safety Instructions For Power Tools

9.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condi- tion. Conductor size must be in accor- dance with the chart below. The amperage rating is listed on the motor or tool name- plate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace damaged exten- sion cords.

Minimum Gauge for Extension Cords

 

 

LENGTH

 

 

 

 

 

 

AMP RATING

25ft

 

50ft

100ft

 

 

 

 

 

0-6

18

 

16

16

 

 

 

 

 

7-10

18

 

16

14

 

 

 

 

 

11-12

16

 

16

14

 

 

 

 

 

13-16

14

 

12

12

 

 

 

 

 

17-20

12

 

12

10

21-30

10

 

10

No

 

 

 

 

 

10.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair cov- ering to contain long hair.

11.ALWAYS USE ANSI-APPROVED SAFE- TY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eye- glasses only have impact resistant lenses, they are NOT safety glasses.

12.SECURE WORK. Use clamps or a vise to hold work when practical. It is safer than using your hand and frees both hands to operate tool.

13.NEVER OVERREACH. Keep proper foot- ing and balance at all times.

14.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories.

15.DISCONNECT TOOLS before servicing and changing accessories, such as blades, bits, cutters, and any other item.

16.REDUCE THE RISK OF UNINTENTION- AL STARTING. Make sure switch is in off position before plugging in. Also, the mag- netic switch on this machine may start if the switch gets bumped hard enough.

17.USE RECOMMENDED ACCESSORIES. Consult the ownerÕs manual for recom- mended accessories. The use of improper accessories may cause risk of injury.

18.CHECK DAMAGED PARTS. Before fur- ther use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, bind- ing of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged must be properly repaired or replaced.

19.NEVER LEAVE TOOL RUNNING UNAT- TENDED. TURN POWER OFF. Do not leave tool until it comes to a complete stop.

20.NEVER USE UNDER THE INFLUENCE of alcohol or drugs, or when tired.

21.IF AT ANY TIME YOU ARE EXPERI- ENCING DIFFICULTIES performing the intended operation, stop using the machine! Then contact our service depart- ment or ask a qualified expert how the operation should be performed.

G1022 Series Table Saws

-3-

Image 5
Contents G1022ZFX G1022SM G1022Z G1022ZFPage Table Of Contents Safety Instructions For Power Tools Safety25ft 50ft 100ft AMP RatingAdditional Safety Instructions For Table Saws Following can help minimize kickbacks Avoiding Kickback Safety AccessoriesFeatherboards Zero Clearance Table InsertsPush Paddles Commentary IntroductionG1022 Series Table Saws 110V Operation Circuit RequirementsModels SM & Z Model ZFModels ZFX, PROZ, & Prozx 220V OperationExtension Cord GroundingTerms and Definitions Machine FeaturesMain Features Unpacking Piece Inventory SET UPMotor with Pulley Hardware Contents Bolt Hardware Recognition ChartSite Considerations Clean UpFloor Load Working ClearanceBeginning Assembly Stand Assembly Models ZF, ZFX, PRO, & Prozx only Stand completely assembledTo mount the handwheels HandwheelsAll Models Motor Checking V-belt alignment Models ZF, ZFX, PROZ, & Prozx SwitchExtension Wings Fence Rails To install and adjust the Model SM fenceFence To mount the rails Models SM & ZAdjust measurement pointer G1022 Series Table Saws Attaching a sacrificial fence To install and adjust the Model Z fenceAttaching a sacrificial fence G1022 Series Table Saws Changing saw blade G1022 Series Table Saws BladeBlade Guard Installing blade guardProper Alignment Added Washers Table Insert Adjusting table insert components G1022 Series Table SawsNext steps for all models Miter GaugeInitial Step Models ZF, ZFX, PROZ, & Prozx Starting the machine Start Up Recommended AdjustmentsRecommended adjustment checklist Blade Selection OperationsVarious saw tooth cutting profiles G1022 Series Table Saws Cross-cut operation G1022 Series Table Saws CrosscuttingRipping operation RippingSingle-blade dado cut Dado CuttingIf the cut is satisfactory, repeat with your fin- ish stock Sacrificial fence G1022 Series Table Saws Rabbet CuttingCutting rabbets with the dado blade Disconnect the machine from the powerCutting rabbets with the standard blade Rabbet cutting G1022 Series Table Saws General MaintenanceLubricate the areas indicated below every 12 months LubricationBelt Date Approximate Hours Of Use Maintenance Performed Blade Parallelism Service AdjustmentsTo shift the trunnion Shim placement G1022 Series Table SawsTo shim the trunnion 45˚ & 90˚ Stops Closure SM and Z Wiring Diagram ZF, ZFX, Proz & Prozx Wiring Diagram Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Models G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx Parts List Switch L-BRACKET Symptom Possible Cause Corrective Action Troubleshooting GuidePush Stick G1022 Series Table Saws G1022 Series Table Saws Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA Page Call Today For a Free Full Color Catalog