Grizzly G1022ZFX instruction manual G1022ZF and ZFX, All Models

Page 20

3.Attach the short upper and lower side braces to one of the assembled side panels. Use the M8 - 1.25 x 16 carriage bolts, 8MM flat wash- ers and M8-1.25 hex nuts as shown in Figure 9.

Figure 9. Assembled stand section.

4.Bolt the other side panel to the upper and lower braces using the M8-1.25 x 16 car- riage bolts, 8MM flat washers and M8-1.25 hex nuts as shown in Figure 10.

Figure 10. Stand completely assembled.

G1022ZF and ZFX:

5.Take the black plastic dust hood with the 4" port and align it with the opening in the adapter. The bolt holes on each of the four corners should line up. Using 10-24 x 3Ú8" bolts, 10-24 nuts and 3Ú16" lock washers to secure the hood to the adapter.

6.Note the location of the mounting holes on the top of the stand. Turn the table saw body upside-down and place the dust hood and adapter assembly over the bottom of the table saw body with the dust port flange pointed up.

All Models:

7.Align the holes at the four corners. Place the assembled stand upside down on the table saw body, and line up its mounting holes. Make certain the side of the stand with the ÒZ SeriesÓ label, if applicable, is on the front side of the machine (the side with the Grizzly label and angle scale). Secure with M8-1.25 x 19 hex bolts, 8MM flat washers and M8-1.25 hex nuts, with the dust port sandwiched between as shown in Figure 11.

Saw Body

 

Dust Hood

 

Adapter

Dust Hood

 

Stand

 

Figure 11. Attaching the stand to the saw base.

8.With the help of a second person, flip the entire table saw unit right side-up and move it into its working position. Level the stand by checking all sides for symmetry. Measure diagonally from top to bottom and adjust the stand so both diagonals are equal. Tighten all of the stand bolts.

-18-

G1022 Series Contractor Saws

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Table SAW Page Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating Additional Safety Instructions For Table Saws Push Sticks Zero Clearance Table InsertsPush Paddles FeatherboardsCommon Definitions, Terms and Phrases Circuit Requirements 110V OperationG1022SM and G1022Z G1022ZF220V Operation G1022ZFX and G1022PROGrounding Extension Cords Introduction CommentaryG1022 Series Contractor Saws Unpacking Piece InventoryHardware Contents Hardware Recognition Chart BoltClean Up Site ConsiderationsStand Assembly AssemblyBeginning Assembly G1022ZF and ZFX All ModelsHandwheelsMotor Attaching pulley guard bracketPage Wiring G1022ZF, G1022ZFX and G1022PROExtension Wings Fence RailsFence BladeAdjusting blade guard Blade GuardPage Adjusting table insert height G1022 Series Contractor Saws Table InsertAdjustments G1022SM FenceAttaching a sacrificial fence G1022 Series Contractor Saws Adjust measurement pointer G1022Z FenceAdjust measurement pointer G1022 Series Contractor Saws Table/trunnion assembly Blade Parallelism¡ blade parallelism measurement 90 Stops Worm Gear Miter GaugeInitial Step, Model G1022ZF and ZFX Next step for all modelsTest Run OperationsPre-Run Check Blade Selection Ripping bladeCrosscutting Various saw tooth cutting profilesRipping Cross-cut operationDado Operations Optional dado blade systemRabbet Operations Sacrificial fence G1022 Series Contractor SawsRabbet cutting G1022 Series Contractor Saws Maintenance GeneralLubrication TablesG1022SM and Z Wiring Diagram G1022ZF, ZFX and PRO Wiring Diagram Closure Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Model G1022ZF/ZFX/PRO Table SAW G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick Warranty Card Warranty and Returns Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA
Top Page Image Contents