Grizzly instruction manual Wiring, G1022ZF, G1022ZFX and G1022PRO

Page 23

7.Place a straightedge across the arbor pulley and the motor pulley. The straightedge should run across both pulleys evenly as shown in Figure 19. Adjust the motor on its mount until pulleys are aligned, then tighten all the mounting bolts.

Figure 19. Checking V-belt alignment.

8.Slip the pulley cover spacer over the pulley cover mounting bolt and fit the plastic pulley cover in place. Secure it with the wing nut provided as shown in Figure 20.

Figure 20. Attaching the pulley guard.

Wiring

G1022SM and G1022Z:

The ON/OFF switch, with attached power cord and plug, is already mounted to the saw enclo- sure. Simply connect the quick disconnect on the cord between the switch and motor.

G1022ZF, G1022ZFX and G1022PRO:

The ON/OFF switch on the ZF, ZFX and PRO models mounts directly below the front fence rail.

1.Take the L-shaped bracket supplied and position it below the front fence rail at the left hand side of the machine. The shorter side of the L has two holes which will align with two holes in the fence rail. Use two Philip¨ head screws to attach the bracket. Thread them in from underneath the rail so the heads are not in the way of the fence travel.

2.Now attach the switch, using two Philips¨ head screws inserted through the back of the bracket and into threaded inserts in the back side of the switch box. Tighten these so the switch box is secure.

3.Connect the quick disconnect on the cord between the switch and motor.




G1022 Series Contractor Saws			-21-

Image 23

Contents Table SAW Page Table Of Contents Safety Instructions For Power Tools SafetyAMP Rating Additional Safety Instructions For Table Saws Zero Clearance Table Inserts Push SticksFeatherboards Push PaddlesCommon Definitions, Terms and Phrases G1022ZF Circuit Requirements110V Operation G1022SM and G1022ZG1022ZFX and G1022PRO 220V OperationGrounding Extension Cords Commentary IntroductionG1022 Series Contractor Saws Piece Inventory UnpackingHardware Contents Bolt Hardware Recognition ChartSite Considerations Clean UpStand Assembly AssemblyBeginning Assembly All Models G1022ZF and ZFXAttaching pulley guard bracket HandwheelsMotorPage G1022ZF, G1022ZFX and G1022PRO WiringFence Rails Extension WingsBlade FenceBlade Guard Adjusting blade guardPage Table Insert Adjusting table insert height G1022 Series Contractor SawsG1022SM Fence AdjustmentsAttaching a sacrificial fence G1022 Series Contractor Saws G1022Z Fence Adjust measurement pointerAdjust measurement pointer G1022 Series Contractor Saws Blade Parallelism Table/trunnion assembly¡ blade parallelism measurement 90 Stops Next step for all models Worm GearMiter Gauge Initial Step, Model G1022ZF and ZFXTest Run OperationsPre-Run Check Ripping blade Blade SelectionVarious saw tooth cutting profiles CrosscuttingCross-cut operation RippingOptional dado blade system Dado OperationsSacrificial fence G1022 Series Contractor Saws Rabbet OperationsRabbet cutting G1022 Series Contractor Saws Tables MaintenanceGeneral LubricationG1022SM and Z Wiring Diagram G1022ZF, ZFX and PRO Wiring Diagram Closure Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Model G1022ZF/ZFX/PRO Table SAW G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO Parts List Switch L-BRACKET Symptom Possible Cause Corrective Action Troubleshooting GuidePush Stick Warranty Card Warranty and Returns Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA