Grizzly G1022ZFX Rabbet Operations, Sacrificial fence G1022 Series Contractor Saws

Page 42

Dadoing operations can also be accomplished using a conventional saw blade. To create a sin- gle-blade dado:

1.Clearly mark the width of the dado cut on your workpiece. Include marks on the edge of your workpiece so you can clearly identify your intended cut while the material is laying flat on the saw table.

2.Set the blade height to the depth of cut you wish to create.

3.If the dado runs the length of the material, adjust the fence so the blade is aligned with the inside of your dado channel as shown in Figure 57B.

4.

Turn on your saw and make the first cut.

Figure 57B. Single-blade dado cut.

5.Turn off the saw and readjust the fence so the blade is aligned with the other edge of the intended dado channel. Be sure to keep the cuts within your marks; otherwise, your dado will be too large.

6.Turn on the saw and make a second cut.

7.Move toward the center of the dado with your subsequent cuts until the dado is complete.

8.Re-install the blade guard.

Rabbet Operations

In addition to its ability to create a variety of dadoes, this table saw can be used to cut L- shaped rabbets. These cuts can be created with a regular saw blade or with specially-designed stacking or wobbling dado blades (Figure 57).

Proper rabbet operation will differ depending on the blade system you choose. Consult the instructions included with your dado blades for directions regarding attachment and adjustment. To use a dado blade for rabbeting operations:

1.Rabbet cutting on the edge of a piece of stock requires the use of a sacrificial fence attachment as shown in Figure 58. The sacrificial fence can be made from a piece of wood that is as long as the metal fence and 3Ú4" thick. Once the sacrificial fence has been cut, attach it to the metal fence with screws or clamps, making sure they are all secure and tight.

Rip Fence

Sacrificial Fence

Dado Insert

Blade Cut-Out

Figure 58. Sacrificial fence.

 

 

 

 

 

 

 

 

-40-

 

 

G1022 Series Contractor Saws

 

 

Image 42
Contents Table SAW Page Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating Additional Safety Instructions For Table Saws Push Sticks Zero Clearance Table InsertsPush Paddles FeatherboardsCommon Definitions, Terms and Phrases G1022SM and G1022Z Circuit Requirements110V Operation G1022ZF220V Operation G1022ZFX and G1022PROGrounding Extension Cords Introduction CommentaryG1022 Series Contractor Saws Unpacking Piece InventoryHardware Contents Hardware Recognition Chart BoltClean Up Site ConsiderationsAssembly Beginning AssemblyStand Assembly G1022ZF and ZFX All ModelsHandwheelsMotor Attaching pulley guard bracketPage Wiring G1022ZF, G1022ZFX and G1022PROExtension Wings Fence RailsFence BladeAdjusting blade guard Blade GuardPage Adjusting table insert height G1022 Series Contractor Saws Table InsertAdjustments G1022SM FenceAttaching a sacrificial fence G1022 Series Contractor Saws Adjust measurement pointer G1022Z FenceAdjust measurement pointer G1022 Series Contractor Saws Table/trunnion assembly Blade Parallelism¡ blade parallelism measurement 90 Stops Initial Step, Model G1022ZF and ZFX Worm GearMiter Gauge Next step for all modelsOperations Pre-Run CheckTest Run Blade Selection Ripping bladeCrosscutting Various saw tooth cutting profilesRipping Cross-cut operationDado Operations Optional dado blade systemRabbet Operations Sacrificial fence G1022 Series Contractor SawsRabbet cutting G1022 Series Contractor Saws Lubrication MaintenanceGeneral TablesG1022SM and Z Wiring Diagram G1022ZF, ZFX and PRO Wiring Diagram Closure Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Model G1022ZF/ZFX/PRO Table SAW G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick Warranty Card Warranty and Returns Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA