Grizzly G1022ZFX instruction manual Fence, Blade

Page 25

Figure 22. Attaching fence rails.

Fence

G1022SM and G1022Z

1.Thread the plastic knob onto the lock handle.

2.Set the lock handle in the up position and slide the fence over the front and rear rails as shown in Figure 23.

Lock Handle

Figure 23. G1022SM fence shown.

3.The fence will require further adjustments, all of which are covered in Adjustments Section.

Blade

Please refer to our current catalog for a complete selection of saw blades. To install the saw blade:

1.Unthread the arbor nut clockwise and remove the outside flange from the arbor. Note that there is a 3Ú4'' diameter spacer on the arbor shaft. Remove and discard it. Remember the arbor nut is a left-handed thread.

2.Install the saw blade onto the arbor. Ensure that the blade teeth point toward you as you stand at the front of the saw. Slide on the flange and thread the arbor nut back on.

3.Use the arbor wrench provided with the saw to tighten the arbor nut. Wedge a block of wood in the teeth of the blade to keep it from turning when tightening the nut as shown in Figure 24.

Figure 24. Changing saw blade.

!Disconnect power to the machine when perform-

ing any maintenance, assembly or adjust- ments. Failure to do this may result in serious personal injury.




G1022 Series Contractor Saws				-23-

Image 25

Contents

Table SAW Page Table Of Contents Safety Instructions For Power Tools SafetyAMP Rating Additional Safety Instructions For Table Saws Zero Clearance Table Inserts Push SticksFeatherboards Push PaddlesCommon Definitions, Terms and Phrases 110V Operation Circuit RequirementsG1022SM and G1022Z G1022ZFG1022ZFX and G1022PRO 220V OperationGrounding Extension Cords Commentary IntroductionG1022 Series Contractor Saws Piece Inventory UnpackingHardware Contents Bolt Hardware Recognition ChartSite Considerations Clean UpBeginning Assembly AssemblyStand Assembly All Models G1022ZF and ZFXAttaching pulley guard bracket HandwheelsMotorPage G1022ZF, G1022ZFX and G1022PRO WiringFence Rails Extension WingsBlade FenceBlade Guard Adjusting blade guardPage Table Insert Adjusting table insert height G1022 Series Contractor SawsG1022SM Fence AdjustmentsAttaching a sacrificial fence G1022 Series Contractor Saws G1022Z Fence Adjust measurement pointerAdjust measurement pointer G1022 Series Contractor Saws Blade Parallelism Table/trunnion assembly¡ blade parallelism measurement 90 Stops Miter Gauge Worm GearInitial Step, Model G1022ZF and ZFX Next step for all modelsPre-Run Check OperationsTest Run Ripping blade Blade SelectionVarious saw tooth cutting profiles CrosscuttingCross-cut operation RippingOptional dado blade system Dado OperationsSacrificial fence G1022 Series Contractor Saws Rabbet OperationsRabbet cutting G1022 Series Contractor Saws General MaintenanceLubrication TablesG1022SM and Z Wiring Diagram G1022ZF, ZFX and PRO Wiring Diagram Closure Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Model G1022ZF/ZFX/PRO Table SAW G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO Parts List Switch L-BRACKET Symptom Possible Cause Corrective Action Troubleshooting GuidePush Stick Warranty Card Warranty and Returns Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA