Grizzly G1022ZFX instruction manual Attaching a sacrificial fence G1022 Series Contractor Saws

Page 30

3.Loosen the rear lock adjustment, the slotted screw on the front of the fence shown in Figure 33, until the rear locking lever ceases to engage the rear rail with the fence in the locked position.

Rear Lock Adjustment

Figure 33. Rear lock adjustment screw.

4.Loosen the adjustment bolts at the top of the fence shown in Figure 34. Move the straight portion of the fence until it is parallel with the miter slot from front to back. Retighten the bolts.

Adjustment Bolts

Figure 34. Adjustment bolts for fence parallelism.

5.Loosen the locking lever until it is approxi- mately two-thirds engaged. Tighten the rear adjusting screw until the rear clamp barely touches the back rail.

6.Loosen the locking lever and slide the fence along the rail. Return the fence to its position at the edge of the miter slot and slowly apply pressure to the lever. If adjustments are cor- rect, the fence should square itself before the rear clamp engages. If the rear clamp engages before the fence is squared, loosen the screw one-quarter turn and retest.

Tip: Attach a piece of 3Ú4" thick hardwood to the blade side of the fence as shown in Figure 35. This will keep thin materials from wedging between the fence and table, and will also protect the fence from coming in contact with the blade when dadoing or ripping thin stock. Remember to adjust measurement scale on rail to compensate for the thickness of the sacrificial fence.

Figure 35. Attaching a sacrificial fence.

-28-

G1022 Series Contractor Saws

Image 30
Contents Table SAW Page Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating Additional Safety Instructions For Table Saws Push Sticks Zero Clearance Table InsertsPush Paddles FeatherboardsCommon Definitions, Terms and Phrases G1022SM and G1022Z Circuit Requirements110V Operation G1022ZF220V Operation G1022ZFX and G1022PROGrounding Extension Cords Introduction CommentaryG1022 Series Contractor Saws Unpacking Piece InventoryHardware Contents Hardware Recognition Chart BoltClean Up Site ConsiderationsAssembly Beginning AssemblyStand Assembly G1022ZF and ZFX All ModelsHandwheelsMotor Attaching pulley guard bracketPage Wiring G1022ZF, G1022ZFX and G1022PROExtension Wings Fence RailsFence BladeAdjusting blade guard Blade GuardPage Adjusting table insert height G1022 Series Contractor Saws Table InsertAdjustments G1022SM FenceAttaching a sacrificial fence G1022 Series Contractor Saws Adjust measurement pointer G1022Z FenceAdjust measurement pointer G1022 Series Contractor Saws Table/trunnion assembly Blade Parallelism¡ blade parallelism measurement 90 Stops Initial Step, Model G1022ZF and ZFX Worm GearMiter Gauge Next step for all modelsOperations Pre-Run CheckTest Run Blade Selection Ripping bladeCrosscutting Various saw tooth cutting profilesRipping Cross-cut operationDado Operations Optional dado blade systemRabbet Operations Sacrificial fence G1022 Series Contractor SawsRabbet cutting G1022 Series Contractor Saws Lubrication MaintenanceGeneral TablesG1022SM and Z Wiring Diagram G1022ZF, ZFX and PRO Wiring Diagram Closure Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Model G1022ZF/ZFX/PRO Table SAW G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick Warranty Card Warranty and Returns Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA