Grizzly G1022ZFX instruction manual Push Sticks, Zero Clearance Table Inserts

Page 7

Statistics prove that most common acci- dents among table saw users can be linked to kickback. Kickback is typically defined as the high-speed expulsion of stock from the table saw toward its opera- tor. In addition to the danger of the opera- tor or others in the area being struck by the flying stock, it is often the case that the operator’s hands are forced into the blade during the kickback. The following can help minimize kickbacks.

1.Use your blade guard and splitter.

2.Never for any reason place your hand behind the blade. Should kickback occur, your hand will be pulled into the blade.

3.Inspect splitter for alignment between it and your blade.

4.Never use the fence as a guide for cross- cutting.

5.Never attempt freehand cuts.

6.Use a push stick or featherboard to maintain control of your workpiece.

7.Feed cuts through to completion.

8.Stand to the side when ripping.

9.Ensure your fence and miter slot are par- allel to the blade.

If you do not have a clear understanding of kickback and how it occurs, do not operate this table saw.

Safety Accessories

Push Sticks

The use of push sticks, particularly when cutting small or narrow workpieces, provides a double benefit for saw operators. The push stick pro- vides added leverage, enabling the operator to keep the workpiece firmly supported against the fence and table. At the same time, the push stick keeps the operatorÕs hand safely away from the rotation of the saw blade as shown in Figure 1. See the template on Page 62 of the manual for construction details, or purchase one from the Grizzly catalog.

Push Stick

Figure 1. Push Stick.

Zero Clearance Table Inserts

Ideal for use when ripping thin strips or making bevel cuts, these prevent tearout and jammed blades by supporting material close to the blade. Use the standard table insert as a template when creating additional inserts from wood or plywood. Blade slot inserts can be custom cut for specific blade angles by raising the running blade into an uncut insert at the angle you desire. Be sure to make an additional slot for the blade splitter. We also carry a wide selection of table inserts shown in Figure 2 in the Grizzly catalog. Be sure to hold the insert firmly in place with a piece of wood when creating slots. Never hold the table insert with your hand while cutting new slots.

G1022 Series Contractor Saws

-5-

Image 7
Contents Table SAW Page Table Of Contents Safety Instructions For Power Tools SafetyAMP Rating Additional Safety Instructions For Table Saws Zero Clearance Table Inserts Push SticksFeatherboards Push PaddlesCommon Definitions, Terms and Phrases G1022ZF Circuit Requirements110V Operation G1022SM and G1022ZG1022ZFX and G1022PRO 220V OperationGrounding Extension Cords Commentary IntroductionG1022 Series Contractor Saws Piece Inventory UnpackingHardware Contents Bolt Hardware Recognition ChartSite Considerations Clean UpBeginning Assembly AssemblyStand Assembly All Models G1022ZF and ZFXAttaching pulley guard bracket HandwheelsMotorPage G1022ZF, G1022ZFX and G1022PRO WiringFence Rails Extension WingsBlade FenceBlade Guard Adjusting blade guardPage Table Insert Adjusting table insert height G1022 Series Contractor SawsG1022SM Fence AdjustmentsAttaching a sacrificial fence G1022 Series Contractor Saws G1022Z Fence Adjust measurement pointerAdjust measurement pointer G1022 Series Contractor Saws Blade Parallelism Table/trunnion assembly¡ blade parallelism measurement 90 Stops Next step for all models Worm GearMiter Gauge Initial Step, Model G1022ZF and ZFXPre-Run Check OperationsTest Run Ripping blade Blade SelectionVarious saw tooth cutting profiles CrosscuttingCross-cut operation RippingOptional dado blade system Dado OperationsSacrificial fence G1022 Series Contractor Saws Rabbet OperationsRabbet cutting G1022 Series Contractor Saws Tables MaintenanceGeneral LubricationG1022SM and Z Wiring Diagram G1022ZF, ZFX and PRO Wiring Diagram Closure Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Model G1022ZF/ZFX/PRO Table SAW G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO Parts List Switch L-BRACKET Symptom Possible Cause Corrective Action Troubleshooting GuidePush Stick Warranty Card Warranty and Returns Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA