Grizzly G1022ZFX instruction manual Operations, Pre-Run Check, Test Run

Page 37

SECTION 6: OPERATIONS

Pre-Run Check

Before you begin to use your Model G1022 Series, you should give it a thorough inspection. While making your inspection, ask yourself the following questions:

1.Are all the fasteners tight?

2.Is the blade mounted correctly?

3.Is the saw stable?

4.Is it wired properly?

5.Is your electrical system properly config- ured?

6.Have you checked your work piece for obvi- ous defects?

7.Are the V-belts properly tensioned and the pulleys properly aligned?

8.Is the guard assembly installed and func- tional?

9.Have you checked the saw blade clearance when it is adjusted to varying angles and depths?

10.Have you read all warnings and directions regarding the operation of this machine?

G1022 Series Contractor Saws

Test Run

!Disconnect power to the machine when perform- ing any maintenance,

assembly or adjust- ments. Failure to do this may result in serious personal injury.

Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back.

Wear safety glasses dur- ing the entire operations process. Failure to com- ply may result in serious personal injury.

Always wear a dust mask when operating the G1022. Using this machine produces saw- dust which may cause allergic reactions or res- piratory problems.

1.Face the table saw and stand to the left of the blade path.

2.With one finger on the START button and one finger on the STOP button, turn the saw on. Be ready to turn it off in case of mishap.

3.Watch and listen to the saw. Note whether there are any unusual sounds or excessive vibrations.

-35-

Image 37

Contents Table SAW Page Table Of Contents Safety Instructions For Power Tools SafetyAMP Rating Additional Safety Instructions For Table Saws Zero Clearance Table Inserts Push SticksFeatherboards Push PaddlesCommon Definitions, Terms and Phrases 110V Operation Circuit RequirementsG1022SM and G1022Z G1022ZFG1022ZFX and G1022PRO 220V OperationGrounding Extension Cords Commentary IntroductionG1022 Series Contractor Saws Piece Inventory UnpackingHardware Contents Bolt Hardware Recognition ChartSite Considerations Clean UpBeginning Assembly AssemblyStand Assembly All Models G1022ZF and ZFXAttaching pulley guard bracket HandwheelsMotorPage G1022ZF, G1022ZFX and G1022PRO WiringFence Rails Extension WingsBlade FenceBlade Guard Adjusting blade guardPage Table Insert Adjusting table insert height G1022 Series Contractor SawsG1022SM Fence AdjustmentsAttaching a sacrificial fence G1022 Series Contractor Saws G1022Z Fence Adjust measurement pointerAdjust measurement pointer G1022 Series Contractor Saws Blade Parallelism Table/trunnion assembly¡ blade parallelism measurement 90 Stops Miter Gauge Worm GearInitial Step, Model G1022ZF and ZFX Next step for all modelsPre-Run Check OperationsTest Run Ripping blade Blade SelectionVarious saw tooth cutting profiles CrosscuttingCross-cut operation RippingOptional dado blade system Dado OperationsSacrificial fence G1022 Series Contractor Saws Rabbet OperationsRabbet cutting G1022 Series Contractor Saws General MaintenanceLubrication TablesG1022SM and Z Wiring Diagram G1022ZF, ZFX and PRO Wiring Diagram Closure Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Model G1022ZF/ZFX/PRO Table SAW G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO Parts List Switch L-BRACKET Symptom Possible Cause Corrective Action Troubleshooting GuidePush Stick Warranty Card Warranty and Returns Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA