Grizzly G1022ZFX instruction manual ¡ blade parallelism measurement

Page 34

7.Now check to see if the blade remains paral- lel to the miter slot when tilted to 45¡.

8.Tilt the blade to 45¡ and repeat Steps 1-5. If the blade is still parallel to the miter slot, con- tinue with the next section. Otherwise, con- tinue with the next step.

9.If the blade was parallel to the miter slot at 90¡ but not at 45¡, the trunnion will need to be shimmed with metal shim stock. The shims are placed between the trunnion cor- ners and the table.

#1 Shim

#3 Shim

#2 Shim		#4 Shim

Figure 44A. 45¡ blade parallelism measurement.

Figure 44B. Shim placement.

#1 Shim

#3 Shim

#2 Shim		#4 Shim

Figure 45. 45¡ blade parallelism measurement.

10.Refer to Figures 43, 44A, 44B and 45, for shim placement. If the distance of A is short- er than B, shim(s) will need to be placed under corners #1 and #2. If the distance of B is shorter than A, shim(s) will need to be placed under corners #3 and #4. Very thin shim stock works well, just make sure they are all the same thickness, and you put an equal number under each of the two corners.

11.Tighten down one trunnion bolt a small amount and then move on to each of the oth- ers, tightening each down the same amount. Continue to rotate through the bolts, tighten- ing them a little each time until they are all secure.

12.Now recheck the blade to miter slot at 90¡ and 45¡ by repeating Steps 1-3 and 8. If the distance of A and B are equal to or less than 0.004" at both 90¡ and 45¡, continue to the next section. If the distances are still off by more than 0.004", repeat Steps 4-12.

13.Once you feel you have the miter slot adjust- ed to the blade, recheck all measurements and be sure the table mounting bolts are secure. Repeat Step 10 in ÒBlade Guard/SplitterÓ instructions. Also, if you ever loosen the trunnion in the future, be sure to make note of shim placements and reassemble exactly how it came apart.




-32-	G1022 Series Contractor Saws

Image 34

Contents Table SAW Page Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating Additional Safety Instructions For Table Saws Push Sticks Zero Clearance Table InsertsPush Paddles FeatherboardsCommon Definitions, Terms and Phrases G1022SM and G1022Z Circuit Requirements110V Operation G1022ZF220V Operation G1022ZFX and G1022PROGrounding Extension Cords Introduction CommentaryG1022 Series Contractor Saws Unpacking Piece InventoryHardware Contents Hardware Recognition Chart BoltClean Up Site ConsiderationsBeginning Assembly AssemblyStand Assembly G1022ZF and ZFX All ModelsHandwheelsMotor Attaching pulley guard bracketPage Wiring G1022ZF, G1022ZFX and G1022PROExtension Wings Fence RailsFence BladeAdjusting blade guard Blade GuardPage Adjusting table insert height G1022 Series Contractor Saws Table InsertAdjustments G1022SM FenceAttaching a sacrificial fence G1022 Series Contractor Saws Adjust measurement pointer G1022Z FenceAdjust measurement pointer G1022 Series Contractor Saws Table/trunnion assembly Blade Parallelism¡ blade parallelism measurement 90 Stops Initial Step, Model G1022ZF and ZFX Worm GearMiter Gauge Next step for all modelsPre-Run Check OperationsTest Run Blade Selection Ripping bladeCrosscutting Various saw tooth cutting profilesRipping Cross-cut operationDado Operations Optional dado blade systemRabbet Operations Sacrificial fence G1022 Series Contractor SawsRabbet cutting G1022 Series Contractor Saws Lubrication MaintenanceGeneral TablesG1022SM and Z Wiring Diagram G1022ZF, ZFX and PRO Wiring Diagram Closure Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Model G1022ZF/ZFX/PRO Table SAW G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick Warranty Card Warranty and Returns Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA