Grizzly instruction manual Greasing, G0503 Grease SCHEDULE/CHECK-OFF Chart

Page 38

Greasing
Tools Needed	Qty
Grease Gun	1
Hardware Needed	Qty
High Temp Bearing Grease	Varies
Multi-Purpose Grease	Varies

Wipe grease fittings clean and lubricate with two pumps of high-temp bearing grease. To lubricate a greased surface; wipe the surface clean and apply a thin coating of multi-purpose grease.

The photos in Figure 47 label the grease fit- tings and greased surfaces by number for easy identification. Match the numbers in Figure 47 to the chart below for proper greasing intervals. Note—This page was designed to be copied and used as a check-off chart to help maintain a regu- lar lubrication schedule.

	3
			4
	1	2
		10	6
5	7
5
	8	9

Figure 47. Lubrication points.

G0503 GREASE SCHEDULE/CHECK-OFF CHART

	(see fig. 47 for
	fitting locations)
Main Wheels	1,2
Blade Tension Slide	3,
conveyor	4,5,6
Elevation Shaft	7,8
Elevation Gear	9
Tension Handle	10

-36-	Model G0503 (Mfg. Since 12/08)

Image 38

Contents Horizontal Resaw Bandsaw Page Table of Contents Accessories Maintenance Introduction Manual Accuracy Contact InfoMain view of machine features and controls IdentificationPage Control Panel Machine Data Safety Safety Instructions for MachineryMany Machines will Eject the Workpiecetowardtheoperator Additional Safety Instructions for Resaws Roll up or button sleeves at the cuffAdditional Safety Instructions for Hydraulics Depressurize for MaintenanceCircuit Requirements 220V 3-Phase 440V 3-PhaseMinimum Wire Requirements Amperage DrawExtension Cords Phase ConverterGrounding Connection TypeUnpacking SET UPAbout this Section Piece InventoryHardware Recognition Chart Items Needed For Set UpClean Up SeeSite Considerations Removing Resaw From the Crate PalletMounting Resaw to Floor Mounting Conveyor BeltAttaching Hydraulics To attach the hydraulic drive to the conveyorTo attach the blade cover Installing Blade CoverAttaching Handwheel Handle To attach the handwheel handleTo mount the control panel Positioning Control PanelMounting To mount the return rollersConnecting to Installing the Blade To connect the resaw to a dust collectorPage Shut off the main power at the power source circuit breaker Connecting to PowerTo connect the resaw to the power source Test Run To adjust the tension Disconnect the resaw from power Blade TensionStock Preparation Operation SafetyOperations To prepare the workpiece for a precision cutTo operate the infeed conveyor Blade HeightConveyor Controls Pressure Rollers Outfeed pressure rollerResawing Blade Information Most common causes of blade breakage areG7895-Citrus Degreaser AccessoriesG1955-OxiSolvBlade & Bit Cleaner H4875 Lenox BladesH4874 H4876P0503A17-440V Conversion Kit H4978 T20446 H4979Miscellaneous MaintenanceCleaning BeltsG0503 Grease SCHEDULE/CHECK-OFF Chart GreasingHydraulic Fluid Hydraulic System Schedule Minor Service Check the hydraulic fluid level dailyHydraulic System Major Service Supplies Needed QtyTo clean the tank screen Wheel ScrapersTracking ServiceAbout Service Page Adjusting Blade Guides To align the guide blocksTo adjust the blade elevation gauge Adjusting Support WheelTo adjust the support wheel Blade Elevation GaugeAdjusting Main Conveyor Table To check the main conveyor table alignmentPage Tracking Conveyor To set the conveyor trackingReplacing Conveyor To replace the conveyor beltsTo adjust the V-belt tension Disconnect the resaw from power Belt Tensioning Replacing V-BeltsRewiring to 220V PowerG0503 Control Panel Maintenance Log Date Approximate Hours Of Use Maintenance Performed101 Model G0503 Mfg. Since 12/08 302 426 Model G0503 Mfg. Since 12/08 Model G0503 Mfg. Since 12/08 Model G0503 Mfg. Since 12/08 815 901 904 905 906 903 908 910 907 FLT A01-1 A16 MOTOR/START MOTOR/STOP Description Lower Hinge Liner WAY Rear Roller ARM Bracket Troubleshooting Symptom Possible Cause Corrective ActionService Log Warranty and Returns Warranty Card Grizzly INDUSTRIAL, inc Box Bellingham, WA Page Order Hours a DAY