Grizzly G0503 instruction manual Control Panel

Page 8

Control Panel

E

F

D

A			C

B

Figure 3. Control panel close-up.

A.EMERGENCY STOP Button—Turns off power to both motors in an emergency.

B.PUMP STOP Button—Stops the hydraulic pump motor.

C.MOTOR STOP Button—Stops the main motor.

D.MOTOR START Button—Starts the main motor and the saw blade.

E.PUMP START Button—Starts the hydraulic pump motor.

F.POWER ON Button—Connects power to both motors.

-6-	Model G0503 (Mfg. Since 12/08)

Image 8

Contents Horizontal Resaw Bandsaw Page Table of Contents Accessories Maintenance Introduction Manual Accuracy Contact InfoMain view of machine features and controls IdentificationPage Control Panel Machine Data Safety Safety Instructions for MachineryMany Machines will Eject the Workpiecetowardtheoperator Additional Safety Instructions for Resaws Roll up or button sleeves at the cuffAdditional Safety Instructions for Hydraulics Depressurize for Maintenance220V 3-Phase 440V 3-Phase Minimum Wire RequirementsCircuit Requirements Amperage DrawPhase Converter GroundingExtension Cords Connection TypeSET UP About this SectionUnpacking Piece InventoryHardware Recognition Chart For Set Up Clean UpItems Needed SeeSite Considerations Removing Resaw From the Crate PalletMounting Resaw to Floor Mounting Conveyor BeltAttaching Hydraulics To attach the hydraulic drive to the conveyorInstalling Blade Cover Attaching Handwheel HandleTo attach the blade cover To attach the handwheel handlePositioning Control Panel MountingTo mount the control panel To mount the return rollersConnecting to Installing the Blade To connect the resaw to a dust collectorPage Shut off the main power at the power source circuit breaker Connecting to PowerTo connect the resaw to the power source Test Run To adjust the tension Disconnect the resaw from power Blade TensionOperation Safety OperationsStock Preparation To prepare the workpiece for a precision cutTo operate the infeed conveyor Blade HeightConveyor Controls Pressure Rollers Outfeed pressure rollerResawing Blade Information Most common causes of blade breakage areG7895-Citrus Degreaser AccessoriesG1955-OxiSolvBlade & Bit Cleaner Lenox Blades H4874H4875 H4876P0503A17-440V Conversion Kit H4978 T20446 H4979Maintenance CleaningMiscellaneous BeltsG0503 Grease SCHEDULE/CHECK-OFF Chart GreasingHydraulic Fluid Hydraulic System Schedule Minor Service Check the hydraulic fluid level dailyHydraulic System Major Service Supplies Needed QtyTo clean the tank screen Wheel ScrapersTracking ServiceAbout Service Page Adjusting Blade Guides To align the guide blocksAdjusting Support Wheel To adjust the support wheelTo adjust the blade elevation gauge Blade Elevation GaugeAdjusting Main Conveyor Table To check the main conveyor table alignmentPage Tracking Conveyor To set the conveyor trackingReplacing Conveyor To replace the conveyor beltsTo adjust the V-belt tension Disconnect the resaw from power Belt Tensioning Replacing V-BeltsRewiring to 220V PowerG0503 Control Panel Maintenance Log Date Approximate Hours Of Use Maintenance Performed101 Model G0503 Mfg. Since 12/08 302 426 Model G0503 Mfg. Since 12/08 Model G0503 Mfg. Since 12/08 Model G0503 Mfg. Since 12/08 815 901 904 905 906 903 908 910 907 FLT A01-1 A16 MOTOR/START MOTOR/STOP Description Lower Hinge Liner WAY Rear Roller ARM Bracket Troubleshooting Symptom Possible Cause Corrective ActionService Log Warranty and Returns Warranty Card Grizzly INDUSTRIAL, inc Box Bellingham, WA Page Order Hours a DAY