Grizzly G0514 owner manual Blade Tracking, To adjust the blade tracking

Page 21

6.Remove the table insert and the table pin from the table, if these are pre-installed.

7.With the blade teeth pointing downward, slide the blade through the table slot.

8.Slide the blade through the upper and lower blade guides, and mount it over the upper and lower wheels.

9.Tighten the quick release tension lever, then install the table insert and table pin.

10.Keep the upper and lower blade guides adjusted away from the blade until the blade tracking and tension have been adjusted.

Blade Tracking

Personal injury or death can occur if the machine starts while your hand is touching the bandsaw wheel during tracking adjustments. Disconnect power from the bandsaw before performing blade tracking adjustments.

During operation, the blade needs to ride on the center of the upper and lower wheels. Adjusting the path the blade travels on is called blade track- ing.

To adjust the blade tracking:

1.Make sure the upper and lower blade guides are adjusted away from the blade.

2.Tension the blade (refer to the "Tensioning Blade" procedure on Page 23).

3.DISCONNECT BANDSAW FROM POWER!

4.Open the upper wheel cover.

Model G0513/G0514 (Mfg. since 8/02+)

5.Loosen the tracking control lock lever shown in Figure 18 by turning it counter-clockwise.

Blade Tracking Knob

Lock Lever

Figure 18. Release lock lever before adjusting tracking.

Be careful when turn- ing the bandsaw wheel by hand in the next step. The spokes may have sharp edges and blade teeth may extend beyond the edge of the wheel and cause injury.

6.Turn the blade tracking knob clockwise or counterclockwise while turning the upper wheel by hand until the blade tracks centered on the wheel.

7.Turn the upper wheel by hand three aditional rotations to ensure the blade tracks on the center of the wheel.

8.Tighten the tracking control lock lever.

9.Close the wheel cover.

10.Reconnect the bandsaw to power.

-19-

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model G0513/G0514 17 & 19 Heavy Duty Bandsaws Ss ,EAD from Leadbased PAINTS Table of Contents Manual Accuracy IntroductionContact Info Machine DescriptionIdentification Tension Lever Adjustment Screw Blade Tension ScaleWheel Brush Machine Data Sheet Table Information Model G0514 19 HEAVY-DUTY Bandsaw 2 HP 143 Safety Safety Instructions for MachineryWearing Proper APPAREL. 9d cdi lZVg Children & BYSTANDERS. @ZZe XaYgZc Additional Safety for Bandsaws Blade Replacement SAFETY. 7ZhYZhYhMAINTENANCE/SERVICE.  6aa cheZXidch! Power Connection Device Power Supply Circuit RequirementsCircuit Requirements Full Load Amperage DrawNeeded for Setup SetupUnpacking Description QtyInventory Box 1 Figures QtyHardware and Tools not shown Qty Hardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadMoving & Placing Base Unit Mounting to Shop FloorBolting to Concrete Floors To install the guide post handwheel To install the tableGuide Post Handwheel Blade Tracking To adjust the blade trackingPositive Stop To set up the positive stopDust Collection Fence Assembly To connect a dust collection hoseTo assemble the fence To adjust the fence parallel to the miter slot Fence AdjustmentTo adjust the miter slot square to the blade Table AlignmentTest Run Tensioning Blade To test run the machineTo tension the bandsaw blade Blade Guides To adjust the upper blade guideFront of lower blade guide Page Overview OperationsStraight Cuts Irregular CutsTo adjust guide post START/STOP Switch Guide PostFine Tune Tracking Table TiltTo tilt the table RippingCrosscutting To make a rip cutTo make a 90˚ crosscut Resawing Cutting CurvesTo make a resaw cut To adjust the blade speed Stacked Cuts Blade SpeedTo complete a stacked cut Blade Information Blade LengthBlade Width Tooth Pitch Tooth StyleBlade Care Blade BreakageMost common causes of blade breakage are Blade ChangesTo remove a blade To replace a bladeAccessories T10117 Big Mouth Dust Hood Cleaning MaintenanceSchedule Unpainted Cast IronLubrication To remove and clean the bearingsTroubleshooting ServiceOnly cut wood and ensure moisture is below 20% Make tight inside cuts Symptom Possible Cause Possible Solution Tensioning V-Belt Checking V-BeltTo check the V-belt Tools Needed QtyTo replace the V-belt Replacing V-BeltAdjusting Wheel Brush Adjusting Tension LeverTo adjust the tension lever, do these steps To adjust the wheel brushTo correct blade lead Blade LeadTo skew your fence To shift the tableChecking Coplanarity Aligning WheelsComponents and Hardware Needed Qty Tools Needed8deaVcVg Cdi8deaVcVg Shimming Upper WheelAdjusting Lower Wheel Adjusting Guide Post TravelTo adjust the lower wheel ⁄4 turn 7gVX`Zi Hb6 JYZ Wiring Safety Instructions WiringG0513/G0514 Wiring Diagram HLI8=KdY&%ZlgZ&iG Main Description Main Parts ListPLW04M Lock Washer 8MM PW01M Flat Washer 8MM PB14M Fence Blade Guide Blade Guide Parts List Description Label Placement10. 8dbbZcih Warranty Card99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns Page Order Hours a DAY

G0514 specifications

The Grizzly G0514 is a top-tier bandsaw designed specifically for serious woodworkers and industrial applications. This machine is celebrated for its powerful cutting capabilities and precision, making it a vital tool for anyone looking to handle large projects with ease.

One of the standout features of the Grizzly G0514 is its robust 2 HP, 220V motor that provides ample power for cutting through thick hardwoods, softwoods, and even non-ferrous metals. This strong motor ensures a stable performance, enabling users to tackle various cutting tasks without worrying about overheating or stalling. Complementing this motor is a dual voltage capability, allowing users to switch between 120V and 220V power sources, making it incredibly versatile for different workshops.

The Grizzly G0514 also boasts a large 17-inch throat capacity, which translates to an impressive resaw height of 12 inches. This means that woodworkers can rip large pieces of timber or veneer with remarkable ease. The 14-inch blade length further enhances its cutting capabilities, providing smooth and clean cuts every time.

Another significant characteristic of this bandsaw is the precision-bearing blade guides. These guides ensure that the blade remains stable during operation, reducing blade deflection and enhancing the quality of cuts. The G0514 is equipped with a heavy-duty cast iron frame and base, which not only ensures stability and durability but also helps minimize vibrations—giving users a smoother cutting experience.

Featuring a rich array of technologies, the Grizzly G0514 is built with user-friendliness in mind. The quick-release blade tension lever allows for speedy adjustments when switching blades, maximizing efficiency. Additionally, it comes with a full-size table measuring 22 inches by 27 inches, providing ample workspace for larger projects.

Safety is paramount in woodworking, and this bandsaw is no exception, featuring a blade brake and an integrated dust port that helps maintain a clean work environment. The G0514 also comes equipped with a fence and miter gauge, enabling accurate cuts and angled woodworking tasks.

In summary, the Grizzly G0514 is an excellent choice for both professional woodworkers and hobbyists alike. With its powerful motor, vast cutting capacity, and user-friendly features, it stands out as a reliable and high-performance bandsaw in the market. Whether you’re crafting intricate furniture or simply doing home projects, the G0514 is designed to meet all your woodworking needs efficiently and safely.
Top Page Image Contents