Grizzly G0514 Checking V-Belt, Tensioning V-Belt, To check the V-belt, Tools Needed Qty

Page 46

Checking V-Belt

To ensure optimum power transmission from the motor to the blade, the V-belt must be in good condition and operate under proper tension. The belt should be checked for cracks, fraying, and wear. Belt tension should be checked at least every 3 months—more often if the bandsaw is used daily.

To check the V-belt:

1.DISCONNECT BANDSAW FROM POWER!

2.Open the lower wheel cover.

3.Note the condition of the V-belt. If the V-belt is cracked, frayed, or glazed; it should be replaced as soon as convenient.

4.Push the center of the V-belt. Note the amount of deflection (Figure 56). If deflec- tion is more than 34", re-tension the V-belt.

7VcYhVl

9Z[aZXi^dc L]ZZa

Bdidg

L]ZZa

Figure 56. V-belt deflection.

-44-

Tensioning V-Belt

Tools Needed:

Qty

Hex Wrench 8mm

1

To tension the V-belt:

 

1.DISCONNECT BANDSAW FROM POWER!

2.Open the lower wheel cover.

3.Loosen the motor mount screws shown in

Figure 57.

Motor

Hinge

Screw

Motor

Adjustment

Screw

Figure 57. Motor mount screws.

4.Rotate the motor to tension the V-belt, then tighten the motor adjustment screw.

5.Push the center of the V-belt. If deflection is approximately 34" with moderate pressure from your thumb or finger, then the tension is correct. If the deflection is more than 34", repeat Steps 3 & 4.

6.When the V-belt tension is correct, tighten the motor hinge screw and close the lower wheel cover.

Model G0513/G0514 (Mfg. 8/02+)

Image 46
Contents Model G0513/G0514 17 & 19 Heavy Duty Bandsaws Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionManual Accuracy Machine DescriptionIdentification Blade Tension Scale Tension Lever Adjustment ScrewWheel Brush Machine Data Sheet Table Information Model G0514 19 HEAVY-DUTY Bandsaw 2 HP 143 Safety Instructions for Machinery SafetyWearing Proper APPAREL. 9d cdi lZVg Children & BYSTANDERS. @ZZe XaYgZc Blade Replacement SAFETY. 7ZhYZhYh Additional Safety for BandsawsMAINTENANCE/SERVICE.  6aa cheZXidch! Circuit Requirements Power Supply Circuit RequirementsPower Connection Device Full Load Amperage DrawUnpacking SetupNeeded for Setup Description QtyBox 1 Figures Qty InventoryHardware and Tools not shown Qty Hardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadMounting to Shop Floor Moving & Placing Base UnitBolting to Concrete Floors To install the table To install the guide post handwheelGuide Post Handwheel To adjust the blade tracking Blade TrackingTo set up the positive stop Positive StopTo connect a dust collection hose Dust Collection Fence AssemblyTo assemble the fence To adjust the miter slot square to the blade Fence AdjustmentTo adjust the fence parallel to the miter slot Table AlignmentTo test run the machine Test Run Tensioning BladeTo tension the bandsaw blade To adjust the upper blade guide Blade GuidesFront of lower blade guide Page Straight Cuts OperationsOverview Irregular CutsSTART/STOP Switch Guide Post To adjust guide postTable Tilt Fine Tune TrackingTo tilt the table To make a rip cut RippingCrosscuttingTo make a 90˚ crosscut Cutting Curves ResawingTo make a resaw cut Stacked Cuts Blade Speed To adjust the blade speedTo complete a stacked cut Blade Length Blade InformationBlade Width Blade Care Tooth StyleTooth Pitch Blade BreakageTo remove a blade Blade ChangesMost common causes of blade breakage are To replace a bladeAccessories T10117 Big Mouth Dust Hood Schedule MaintenanceCleaning Unpainted Cast IronTo remove and clean the bearings LubricationService TroubleshootingOnly cut wood and ensure moisture is below 20% Make tight inside cuts Symptom Possible Cause Possible Solution To check the V-belt Checking V-BeltTensioning V-Belt Tools Needed QtyReplacing V-Belt To replace the V-beltTo adjust the tension lever, do these steps Adjusting Tension LeverAdjusting Wheel Brush To adjust the wheel brushTo skew your fence Blade LeadTo correct blade lead To shift the tableComponents and Hardware Needed Qty Aligning WheelsChecking Coplanarity Tools NeededShimming Upper Wheel 8deaVcVg Cdi8deaVcVgAdjusting Guide Post Travel Adjusting Lower WheelTo adjust the lower wheel ⁄4 turn 7gVX`Zi Hb6 JYZ Wiring Wiring Safety InstructionsHLI8= G0513/G0514 Wiring DiagramKdY&%ZlgZ&iG Main Main Parts List DescriptionPLW04M Lock Washer 8MM PW01M Flat Washer 8MM PB14M Fence Blade Guide Blade Guide Parts List Label Placement DescriptionWarranty Card 10. 8dbbZcih99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns Page Order Hours a DAY

G0514 specifications

The Grizzly G0514 is a top-tier bandsaw designed specifically for serious woodworkers and industrial applications. This machine is celebrated for its powerful cutting capabilities and precision, making it a vital tool for anyone looking to handle large projects with ease.

One of the standout features of the Grizzly G0514 is its robust 2 HP, 220V motor that provides ample power for cutting through thick hardwoods, softwoods, and even non-ferrous metals. This strong motor ensures a stable performance, enabling users to tackle various cutting tasks without worrying about overheating or stalling. Complementing this motor is a dual voltage capability, allowing users to switch between 120V and 220V power sources, making it incredibly versatile for different workshops.

The Grizzly G0514 also boasts a large 17-inch throat capacity, which translates to an impressive resaw height of 12 inches. This means that woodworkers can rip large pieces of timber or veneer with remarkable ease. The 14-inch blade length further enhances its cutting capabilities, providing smooth and clean cuts every time.

Another significant characteristic of this bandsaw is the precision-bearing blade guides. These guides ensure that the blade remains stable during operation, reducing blade deflection and enhancing the quality of cuts. The G0514 is equipped with a heavy-duty cast iron frame and base, which not only ensures stability and durability but also helps minimize vibrations—giving users a smoother cutting experience.

Featuring a rich array of technologies, the Grizzly G0514 is built with user-friendliness in mind. The quick-release blade tension lever allows for speedy adjustments when switching blades, maximizing efficiency. Additionally, it comes with a full-size table measuring 22 inches by 27 inches, providing ample workspace for larger projects.

Safety is paramount in woodworking, and this bandsaw is no exception, featuring a blade brake and an integrated dust port that helps maintain a clean work environment. The G0514 also comes equipped with a fence and miter gauge, enabling accurate cuts and angled woodworking tasks.

In summary, the Grizzly G0514 is an excellent choice for both professional woodworkers and hobbyists alike. With its powerful motor, vast cutting capacity, and user-friendly features, it stands out as a reliable and high-performance bandsaw in the market. Whether you’re crafting intricate furniture or simply doing home projects, the G0514 is designed to meet all your woodworking needs efficiently and safely.