Grizzly G0514 owner manual

Page 28

4.Loosen the thumb screws shown in Figure 31 and slide the guide bearings away from the blade.

5.Loosen cap screw #2 shown in Figure 30 and adjust the guide block assembly until the front edge of the guide bearings are aligned 116" behind the gullet line as shown in Figure 32. Retighten cap screw #2.

6.Slide the guide bearings against the side of the blade. Make sure the front edge of the bearings are still behind the gullet line. The gap between the face of each guide bear- ing and the side of the blade needs to be the same as the thickness of a dollar bill or approximately 0.004" as shown in Figure 33. Tighten the thumb screws once the guide bearings are correctly set.

7.Turn the adjustment knob shown in Figure 30 to slide the support bearing forward against the back edge of the blade and then back the bearing off approximately 0.016" as shown in Figure 29. Tighten cap screw #1 to secure the bearing in place.

8.Re-install the blade guards.

(Not To Scale)

116" Gap

Gullet Line

Guide Bearing

Blade

 

Figure 32. Correct guide bearing alignment

against the blade.

Guide Bearings

0.004" Gap

Blade

(Not To Scale)

Figure 33. Correct gap between the

guide bearings and the blade.

(Not To Scale)

0.016" Gap

Blade

Support Bearing

Figure 34. Correct gap between the

support bearing and the blade.

-26-

Model G0513/G0514 (Mfg. 8/02+)

Image 28
Contents Model G0513/G0514 17 & 19 Heavy Duty Bandsaws Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Manual AccuracyContact Info Machine DescriptionIdentification Blade Tension Scale Tension Lever Adjustment ScrewWheel Brush Machine Data Sheet Table Information Model G0514 19 HEAVY-DUTY Bandsaw 2 HP 143 Safety Instructions for Machinery SafetyWearing Proper APPAREL. 9d cdi lZVg Children & BYSTANDERS. @ZZe XaYgZc Blade Replacement SAFETY. 7ZhYZhYh Additional Safety for BandsawsMAINTENANCE/SERVICE.  6aa cheZXidch! Power Supply Circuit Requirements Power Connection DeviceCircuit Requirements Full Load Amperage DrawSetup Needed for SetupUnpacking Description QtyBox 1 Figures Qty InventoryHardware and Tools not shown Qty Hardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadMounting to Shop Floor Moving & Placing Base UnitBolting to Concrete Floors To install the table To install the guide post handwheelGuide Post Handwheel To adjust the blade tracking Blade TrackingTo set up the positive stop Positive StopTo connect a dust collection hose Dust Collection Fence AssemblyTo assemble the fence Fence Adjustment To adjust the fence parallel to the miter slotTo adjust the miter slot square to the blade Table AlignmentTo test run the machine Test Run Tensioning BladeTo tension the bandsaw blade To adjust the upper blade guide Blade GuidesFront of lower blade guide Page Operations OverviewStraight Cuts Irregular CutsSTART/STOP Switch Guide Post To adjust guide postTable Tilt Fine Tune TrackingTo tilt the table To make a rip cut RippingCrosscuttingTo make a 90˚ crosscut Cutting Curves ResawingTo make a resaw cut Stacked Cuts Blade Speed To adjust the blade speedTo complete a stacked cut Blade Length Blade InformationBlade Width Tooth Style Tooth PitchBlade Care Blade BreakageBlade Changes Most common causes of blade breakage areTo remove a blade To replace a bladeAccessories T10117 Big Mouth Dust Hood Maintenance CleaningSchedule Unpainted Cast IronTo remove and clean the bearings LubricationService TroubleshootingOnly cut wood and ensure moisture is below 20% Make tight inside cuts Symptom Possible Cause Possible Solution Checking V-Belt Tensioning V-BeltTo check the V-belt Tools Needed QtyReplacing V-Belt To replace the V-beltAdjusting Tension Lever Adjusting Wheel BrushTo adjust the tension lever, do these steps To adjust the wheel brushBlade Lead To correct blade leadTo skew your fence To shift the tableAligning Wheels Checking CoplanarityComponents and Hardware Needed Qty Tools NeededShimming Upper Wheel 8deaVcVg Cdi8deaVcVgAdjusting Guide Post Travel Adjusting Lower WheelTo adjust the lower wheel ⁄4 turn 7gVX`Zi Hb6 JYZ Wiring Wiring Safety InstructionsHLI8= G0513/G0514 Wiring DiagramKdY&%ZlgZ&iG Main Main Parts List DescriptionPLW04M Lock Washer 8MM PW01M Flat Washer 8MM PB14M Fence Blade Guide Blade Guide Parts List Label Placement DescriptionWarranty Card 10. 8dbbZcih99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns Page Order Hours a DAY

G0514 specifications

The Grizzly G0514 is a top-tier bandsaw designed specifically for serious woodworkers and industrial applications. This machine is celebrated for its powerful cutting capabilities and precision, making it a vital tool for anyone looking to handle large projects with ease.

One of the standout features of the Grizzly G0514 is its robust 2 HP, 220V motor that provides ample power for cutting through thick hardwoods, softwoods, and even non-ferrous metals. This strong motor ensures a stable performance, enabling users to tackle various cutting tasks without worrying about overheating or stalling. Complementing this motor is a dual voltage capability, allowing users to switch between 120V and 220V power sources, making it incredibly versatile for different workshops.

The Grizzly G0514 also boasts a large 17-inch throat capacity, which translates to an impressive resaw height of 12 inches. This means that woodworkers can rip large pieces of timber or veneer with remarkable ease. The 14-inch blade length further enhances its cutting capabilities, providing smooth and clean cuts every time.

Another significant characteristic of this bandsaw is the precision-bearing blade guides. These guides ensure that the blade remains stable during operation, reducing blade deflection and enhancing the quality of cuts. The G0514 is equipped with a heavy-duty cast iron frame and base, which not only ensures stability and durability but also helps minimize vibrations—giving users a smoother cutting experience.

Featuring a rich array of technologies, the Grizzly G0514 is built with user-friendliness in mind. The quick-release blade tension lever allows for speedy adjustments when switching blades, maximizing efficiency. Additionally, it comes with a full-size table measuring 22 inches by 27 inches, providing ample workspace for larger projects.

Safety is paramount in woodworking, and this bandsaw is no exception, featuring a blade brake and an integrated dust port that helps maintain a clean work environment. The G0514 also comes equipped with a fence and miter gauge, enabling accurate cuts and angled woodworking tasks.

In summary, the Grizzly G0514 is an excellent choice for both professional woodworkers and hobbyists alike. With its powerful motor, vast cutting capacity, and user-friendly features, it stands out as a reliable and high-performance bandsaw in the market. Whether you’re crafting intricate furniture or simply doing home projects, the G0514 is designed to meet all your woodworking needs efficiently and safely.