Grizzly G0514 owner manual Fine Tune Tracking, Table Tilt, To tilt the table

Page 31

Fine Tune Tracking

NOTICE

Adjusting the final blade tracking setting requires the machine to be turned ON.

To fine tune the tracking:

1.Perform the Blade Tracking procedure on

Page 19.

2.Close the wheel covers and turn the bandsaw

ON.

3.Observe the blade tracking path through the clear window on the right edge of the bandsaw as shown in Figure 37.

Figure 37. Blade tracking window.

4.Loosen the tracking control lock lever (refer to Page 19, Figure 18), then use the tracking knob to adjust the blade so it tracks on the center of the wheel.

5.When you are satisfied with the blade adjust- ment, tighten the lock lever so the knob can- not move.

Table Tilt

Personal injury or death can occur if the bandsaw starts during table adjust- ment. Disconnect power from the bandsaw before performing table adjust- ments.

The bandsaw table will tilt 10˚ left and 45˚ right to provide a wide range of cutting options. Remove the positive stop bolt to tilt the table to the left.

To tilt the table:

1.DISCONNECT BANDSAW FROM POWER!

2.Loosen the lock handle on the table trunnion shown in Figure 38.

Angle Indicator Scale

Located On Opposite Face

Table Tilt Knob

Lock Handle

Figure 38. Table tilt controls.

3.Turn the table tilt knob to position the table to the desired angle of tilt. Refer to the angle gauge on the front table trunnion for the tilting angle.

4.Retighten the lock handle to secure the table.

Model G0513/G0514 (Mfg. since 8/02+)

-29-

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Model G0513/G0514 17 & 19 Heavy Duty Bandsaws Ss ,EAD from Leadbased PAINTS Table of Contents Machine Description IntroductionManual Accuracy Contact InfoIdentification Blade Tension Scale Tension Lever Adjustment ScrewWheel Brush Machine Data Sheet Table Information Model G0514 19 HEAVY-DUTY Bandsaw 2 HP 143 Safety Instructions for Machinery SafetyWearing Proper APPAREL. 9d cdi lZVg Children & BYSTANDERS. @ZZe XaYgZc Blade Replacement SAFETY. 7ZhYZhYh Additional Safety for BandsawsMAINTENANCE/SERVICE.  6aa cheZXidch! Full Load Amperage Draw Power Supply Circuit RequirementsPower Connection Device Circuit RequirementsDescription Qty SetupNeeded for Setup UnpackingBox 1 Figures Qty InventoryHardware and Tools not shown Qty Hardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsMounting to Shop Floor Moving & Placing Base UnitBolting to Concrete Floors To install the table To install the guide post handwheelGuide Post Handwheel Blade Tracking To adjust the blade trackingPositive Stop To set up the positive stopTo connect a dust collection hose Dust Collection Fence AssemblyTo assemble the fence Table Alignment Fence AdjustmentTo adjust the fence parallel to the miter slot To adjust the miter slot square to the bladeTo test run the machine Test Run Tensioning BladeTo tension the bandsaw blade Blade Guides To adjust the upper blade guideFront of lower blade guide Page Irregular Cuts OperationsOverview Straight CutsTo adjust guide post START/STOP Switch Guide PostTable Tilt Fine Tune TrackingTo tilt the table To make a rip cut RippingCrosscuttingTo make a 90˚ crosscut Cutting Curves ResawingTo make a resaw cut Stacked Cuts Blade Speed To adjust the blade speedTo complete a stacked cut Blade Length Blade InformationBlade Width Blade Breakage Tooth StyleTooth Pitch Blade CareTo replace a blade Blade ChangesMost common causes of blade breakage are To remove a bladeAccessories T10117 Big Mouth Dust Hood Unpainted Cast Iron MaintenanceCleaning ScheduleLubrication To remove and clean the bearingsTroubleshooting ServiceOnly cut wood and ensure moisture is below 20% Make tight inside cuts Symptom Possible Cause Possible Solution Tools Needed Qty Checking V-BeltTensioning V-Belt To check the V-beltTo replace the V-belt Replacing V-BeltTo adjust the wheel brush Adjusting Tension LeverAdjusting Wheel Brush To adjust the tension lever, do these stepsTo shift the table Blade LeadTo correct blade lead To skew your fenceTools Needed Aligning WheelsChecking Coplanarity Components and Hardware Needed Qty8deaVcVg Cdi8deaVcVg Shimming Upper WheelAdjusting Guide Post Travel Adjusting Lower WheelTo adjust the lower wheel ⁄4 turn 7gVX`Zi Hb6 JYZ Wiring Safety Instructions WiringHLI8= G0513/G0514 Wiring DiagramKdY&%ZlgZ&iG Main Description Main Parts ListPLW04M Lock Washer 8MM PW01M Flat Washer 8MM PB14M Fence Blade Guide Blade Guide Parts List Description Label Placement10. 8dbbZcih Warranty Card99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns Page Order Hours a DAY

G0514 specifications

The Grizzly G0514 is a top-tier bandsaw designed specifically for serious woodworkers and industrial applications. This machine is celebrated for its powerful cutting capabilities and precision, making it a vital tool for anyone looking to handle large projects with ease.

One of the standout features of the Grizzly G0514 is its robust 2 HP, 220V motor that provides ample power for cutting through thick hardwoods, softwoods, and even non-ferrous metals. This strong motor ensures a stable performance, enabling users to tackle various cutting tasks without worrying about overheating or stalling. Complementing this motor is a dual voltage capability, allowing users to switch between 120V and 220V power sources, making it incredibly versatile for different workshops.

The Grizzly G0514 also boasts a large 17-inch throat capacity, which translates to an impressive resaw height of 12 inches. This means that woodworkers can rip large pieces of timber or veneer with remarkable ease. The 14-inch blade length further enhances its cutting capabilities, providing smooth and clean cuts every time.

Another significant characteristic of this bandsaw is the precision-bearing blade guides. These guides ensure that the blade remains stable during operation, reducing blade deflection and enhancing the quality of cuts. The G0514 is equipped with a heavy-duty cast iron frame and base, which not only ensures stability and durability but also helps minimize vibrations—giving users a smoother cutting experience.

Featuring a rich array of technologies, the Grizzly G0514 is built with user-friendliness in mind. The quick-release blade tension lever allows for speedy adjustments when switching blades, maximizing efficiency. Additionally, it comes with a full-size table measuring 22 inches by 27 inches, providing ample workspace for larger projects.

Safety is paramount in woodworking, and this bandsaw is no exception, featuring a blade brake and an integrated dust port that helps maintain a clean work environment. The G0514 also comes equipped with a fence and miter gauge, enabling accurate cuts and angled woodworking tasks.

In summary, the Grizzly G0514 is an excellent choice for both professional woodworkers and hobbyists alike. With its powerful motor, vast cutting capacity, and user-friendly features, it stands out as a reliable and high-performance bandsaw in the market. Whether you’re crafting intricate furniture or simply doing home projects, the G0514 is designed to meet all your woodworking needs efficiently and safely.
Top Page Image Contents