Grizzly G0514 owner manual Label Placement, Description

Page 63

Label Placement

&-*

&-+&-)

&,,

&,.

&-%

&-'

&-.

&-&

&.%

&,-

&,-

&--

&-(

&-,

&-'

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

177	P0513177	MACHINE WARNING/ID (G0513)
177	P0514177	MACHINE WARNING/ID (G0514)
178	PLABEL-14	ELECTRICITY LABEL
179	PLABEL-11	SAFETY GLASSES 2" X 3 5/16"
180	PLABEL-12	READ MANUAL 2" X 3 5/16"
181	PLABEL-19	HANDS/BS BLADE 2"X3 5/16"H
182	PLABEL-20	DONT OPEN 2"W X 3 5/16"H
183	PLABEL-18	UNPLUG BANDSAW LABEL

184	G8588	GRIZZLY NAMEPLATE- SMALL
185	P0513185	SAW TENSION LABEL
186	P0513186	G0513 LABEL
186	P0514186	G0514 LABEL
187	PPAINT-1	GRIZZLY GREEN TOUCH-UP PAINT
188	PPAINT-10	LIGHT GRAY REF PAINT
189	P0513189	GUIDE POST ADJUST LABEL
190	P0513190	BS BLADE ENCLOSURE LABEL

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

Model G0513/G0514 (Mfg. since 8/02+)

-61-

Image 63

Contents

Model G0513/G0514 17 & 19 Heavy Duty Bandsaws Ss ,EAD from Leadbased PAINTS Table of Contents Machine Description IntroductionManual Accuracy Contact InfoIdentification Tension Lever Adjustment Screw Blade Tension ScaleWheel Brush Machine Data Sheet Table Information Model G0514 19 HEAVY-DUTY Bandsaw 2 HP 143 Safety Safety Instructions for MachineryWearing Proper APPAREL. 9d cdi lZVg Children & BYSTANDERS. @ZZe XaYgZc Additional Safety for Bandsaws Blade Replacement SAFETY. 7ZhYZhYhMAINTENANCE/SERVICE. 6aa cheZXidch! Full Load Amperage Draw Power Supply Circuit RequirementsPower Connection Device Circuit RequirementsDescription Qty SetupNeeded for Setup UnpackingInventory Box 1 Figures QtyHardware and Tools not shown Qty Hardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsMoving & Placing Base Unit Mounting to Shop FloorBolting to Concrete Floors To install the guide post handwheel To install the tableGuide Post Handwheel Blade Tracking To adjust the blade trackingPositive Stop To set up the positive stopDust Collection Fence Assembly To connect a dust collection hoseTo assemble the fence Table Alignment Fence AdjustmentTo adjust the fence parallel to the miter slot To adjust the miter slot square to the bladeTest Run Tensioning Blade To test run the machineTo tension the bandsaw blade Blade Guides To adjust the upper blade guideFront of lower blade guide Page Irregular Cuts OperationsOverview Straight CutsTo adjust guide post START/STOP Switch Guide PostFine Tune Tracking Table TiltTo tilt the table RippingCrosscutting To make a rip cutTo make a 90˚ crosscut Resawing Cutting CurvesTo make a resaw cut To adjust the blade speed Stacked Cuts Blade SpeedTo complete a stacked cut Blade Information Blade LengthBlade Width Blade Breakage Tooth StyleTooth Pitch Blade CareTo replace a blade Blade ChangesMost common causes of blade breakage are To remove a bladeAccessories T10117 Big Mouth Dust Hood Unpainted Cast Iron MaintenanceCleaning ScheduleLubrication To remove and clean the bearingsTroubleshooting ServiceOnly cut wood and ensure moisture is below 20% Make tight inside cuts Symptom Possible Cause Possible Solution Tools Needed Qty Checking V-BeltTensioning V-Belt To check the V-beltTo replace the V-belt Replacing V-BeltTo adjust the wheel brush Adjusting Tension LeverAdjusting Wheel Brush To adjust the tension lever, do these stepsTo shift the table Blade LeadTo correct blade lead To skew your fenceTools Needed Aligning WheelsChecking Coplanarity Components and Hardware Needed Qty8deaVcVg Cdi8deaVcVg Shimming Upper WheelAdjusting Lower Wheel Adjusting Guide Post TravelTo adjust the lower wheel ⁄4 turn 7gVX`Zi Hb6 JYZ Wiring Safety Instructions WiringG0513/G0514 Wiring Diagram HLI8=KdY&%ZlgZ&iG Main Description Main Parts List PLW04M Lock Washer 8MM PW01M Flat Washer 8MM PB14M Fence Blade Guide Blade Guide Parts List Description Label Placement10. 8dbbZcih Warranty Card99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns Page Order Hours a DAY