Grizzly G0514 Adjusting Tension Lever, Adjusting Wheel Brush, To adjust the wheel brush

Page 48

Adjusting Tension

Lever

The quick release tension lever is setup cor- rectly for use with the preinstalled 1311⁄2" blade. However, if you install a different length blade, you will need to adjust the tension lever adjustment screw (Figure 59) so the quick release tension lever works correctly.

5.Thread the tension adjustment screw (Figure 59) down until it contacts the wheel block plate, then back it off 1-2 turns.

6.Tighten the jam nut.

Adjusting Wheel

Brush

Wheel Block

Plate

Tension

Adjustment

Screw

Jam Nut

The lower wheel compartment contains two wheel brushes, one of which is shown in Figure 60. These brushes are designed to sweep sawdust off the wheel tire as the bandsaw is operating. In order to work properly each brush must make contact with the wheel.

Figure 59. Example of quick release tension

lever adjustment screw.

Tools Needed:

Qty

Hex Wrench 5mm.

............................................. 1

Wrench 10mm

1

To adjust the tension lever, do these steps:

1.DISCONNECT BANDSAW FROM POWER!

2.Open the wheel covers, remove the bandsaw blade, then install the new one (refer to Blade Changes, Page 35).

3.Loosen the jam nut on the tension adjustment screw 7-10 turns.

4.Put the quick release tension lever in the down (engaged) position, then turn the blade tension handwheel until the blade tension matches the mark on the blade tension scale for the appropriate blade thickness.

-46-

Wheel Brush

Figure 60. A wheel brush (one of two shown).

Tools Needed:

Qty

Wrench/Socket 10mm

2

To adjust the wheel brush:

 

1.DISCONNECT BANDSAW FROM POWER!

2.Open the lower wheel cover.

3.Loosen the bolt/nut that secures the wheel brush in place.

4.Adjust the wheel brush so it makes good con- tact with the wheel.

5.Tighten the bolt/nut to secure the wheel brush in place.

Model G0513/G0514 (Mfg. 8/02+)

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Model G0513/G0514 17 & 19 Heavy Duty Bandsaws Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Manual AccuracyContact Info Machine DescriptionIdentification Tension Lever Adjustment Screw Blade Tension ScaleWheel Brush Machine Data Sheet Table Information Model G0514 19 HEAVY-DUTY Bandsaw 2 HP 143 Safety Safety Instructions for MachineryWearing Proper APPAREL. 9d cdi lZVg Children & BYSTANDERS. @ZZe XaYgZc Additional Safety for Bandsaws Blade Replacement SAFETY. 7ZhYZhYhMAINTENANCE/SERVICE.  6aa cheZXidch! Power Supply Circuit Requirements Power Connection DeviceCircuit Requirements Full Load Amperage DrawSetup Needed for SetupUnpacking Description QtyInventory Box 1 Figures QtyHardware and Tools not shown Qty Hardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadMoving & Placing Base Unit Mounting to Shop FloorBolting to Concrete Floors To install the guide post handwheel To install the tableGuide Post Handwheel To adjust the blade tracking Blade TrackingTo set up the positive stop Positive StopDust Collection Fence Assembly To connect a dust collection hoseTo assemble the fence Fence Adjustment To adjust the fence parallel to the miter slotTo adjust the miter slot square to the blade Table AlignmentTest Run Tensioning Blade To test run the machineTo tension the bandsaw blade To adjust the upper blade guide Blade GuidesFront of lower blade guide Page Operations OverviewStraight Cuts Irregular CutsSTART/STOP Switch Guide Post To adjust guide postFine Tune Tracking Table TiltTo tilt the table RippingCrosscutting To make a rip cutTo make a 90˚ crosscut Resawing Cutting CurvesTo make a resaw cut To adjust the blade speed Stacked Cuts Blade SpeedTo complete a stacked cut Blade Information Blade LengthBlade Width Tooth Style Tooth PitchBlade Care Blade BreakageBlade Changes Most common causes of blade breakage areTo remove a blade To replace a bladeAccessories T10117 Big Mouth Dust Hood Maintenance CleaningSchedule Unpainted Cast IronTo remove and clean the bearings LubricationService TroubleshootingOnly cut wood and ensure moisture is below 20% Make tight inside cuts Symptom Possible Cause Possible Solution Checking V-Belt Tensioning V-BeltTo check the V-belt Tools Needed QtyReplacing V-Belt To replace the V-beltAdjusting Tension Lever Adjusting Wheel BrushTo adjust the tension lever, do these steps To adjust the wheel brushBlade Lead To correct blade leadTo skew your fence To shift the tableAligning Wheels Checking CoplanarityComponents and Hardware Needed Qty Tools NeededShimming Upper Wheel 8deaVcVg Cdi8deaVcVgAdjusting Lower Wheel Adjusting Guide Post TravelTo adjust the lower wheel ⁄4 turn 7gVX`Zi Hb6 JYZ Wiring Wiring Safety InstructionsG0513/G0514 Wiring Diagram HLI8=KdY&%ZlgZ&iG Main Main Parts List DescriptionPLW04M Lock Washer 8MM PW01M Flat Washer 8MM PB14M Fence Blade Guide Blade Guide Parts List Label Placement DescriptionWarranty Card 10. 8dbbZcih99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns Page Order Hours a DAY

G0514 specifications

The Grizzly G0514 is a top-tier bandsaw designed specifically for serious woodworkers and industrial applications. This machine is celebrated for its powerful cutting capabilities and precision, making it a vital tool for anyone looking to handle large projects with ease.

One of the standout features of the Grizzly G0514 is its robust 2 HP, 220V motor that provides ample power for cutting through thick hardwoods, softwoods, and even non-ferrous metals. This strong motor ensures a stable performance, enabling users to tackle various cutting tasks without worrying about overheating or stalling. Complementing this motor is a dual voltage capability, allowing users to switch between 120V and 220V power sources, making it incredibly versatile for different workshops.

The Grizzly G0514 also boasts a large 17-inch throat capacity, which translates to an impressive resaw height of 12 inches. This means that woodworkers can rip large pieces of timber or veneer with remarkable ease. The 14-inch blade length further enhances its cutting capabilities, providing smooth and clean cuts every time.

Another significant characteristic of this bandsaw is the precision-bearing blade guides. These guides ensure that the blade remains stable during operation, reducing blade deflection and enhancing the quality of cuts. The G0514 is equipped with a heavy-duty cast iron frame and base, which not only ensures stability and durability but also helps minimize vibrations—giving users a smoother cutting experience.

Featuring a rich array of technologies, the Grizzly G0514 is built with user-friendliness in mind. The quick-release blade tension lever allows for speedy adjustments when switching blades, maximizing efficiency. Additionally, it comes with a full-size table measuring 22 inches by 27 inches, providing ample workspace for larger projects.

Safety is paramount in woodworking, and this bandsaw is no exception, featuring a blade brake and an integrated dust port that helps maintain a clean work environment. The G0514 also comes equipped with a fence and miter gauge, enabling accurate cuts and angled woodworking tasks.

In summary, the Grizzly G0514 is an excellent choice for both professional woodworkers and hobbyists alike. With its powerful motor, vast cutting capacity, and user-friendly features, it stands out as a reliable and high-performance bandsaw in the market. Whether you’re crafting intricate furniture or simply doing home projects, the G0514 is designed to meet all your woodworking needs efficiently and safely.
Top Page Image Contents