Grizzly G0514 Full Load Amperage Draw, Power Supply Circuit Requirements, Extension Cords

Page 14

SECTION 2: CIRCUIT REQUIREMENTS

Serious personal injury could occur if you connect the machine to power before com- pleting the setup process. DO NOT connect the machine to the power until instructed later in this manual.

Electrocution or fire could result if machine is not grounded and installed in compliance with electrical codes. Compliance MUST be verified by a qualified electrician!

NOTICE

The Model G0513/G0514 is prewired for 220V. If you plan to operate the machine at 110V, the motor must be rewired (see Page 54) and a 110V plug must be installed.

Full Load Amperage Draw

This machine draws the following amps under maximum load:

Amp Draw at 220V (prewired)

10 Amps

Amp Draw at 110V

20 Amps

Power Supply Circuit Requirements

The power supply circuit for your machine MUST be grounded and rated for the amperage given below. Never replace a circuit breaker on an exist- ing circuit with one of higher amperage without consulting a qualified electrician to ensure compli- ance with wiring codes. If you are unsure about the wiring codes in your area or you plan to connect your machine to a shared circuit, con- sult a qualified electrician.

Minimum Circuit Size (220V)

15

Amps

Minimum Circuit Size (110V)

30

Amps

-12-

 

 

Power Connection Device

The type of plug required to connect your machine to power depends on the type of service you cur- rently have or plan to install. We recommend using one of the plugs shown in Figure 7.

L5-30 GROUNDED

 

LOCKING

 

RECEPTACLE

 

CZjigVa

L5-30 Plug & Outlet

L5-30

for 110V

LOCKING

PLUG

 

=di

 

<gdjcY^c\Egdc\

 

^h=dd`ZY

 

GROUNDED

 

6-15 RECEPTACLE

 

8jggZci8Vggn^c\Egdc\h

6-15 Plug & Outlet

6-15 PLUG

for 220V

 

<gdjcY^c\Egdc\

 

Figure 7. Recommended plug types.

Extension Cords

Using extension cords may reduce the life of the motor. Instead, place the machine near a power source. If you must use an extension cord:

For 110V, use at least a 12 gauge cord that does not exceed 50 feet in length.

For 220V, use at least a 14 gauge cord that does not exceed 50 feet in length.

The extension cord must have a ground wire and plug pin.

Model G0513/G0514 (Mfg. 8/02+)

Image 14
Contents Model G0513/G0514 17 & 19 Heavy Duty Bandsaws Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionManual Accuracy Machine DescriptionIdentification Wheel Brush Tension Lever Adjustment ScrewBlade Tension Scale Machine Data Sheet Table Information Model G0514 19 HEAVY-DUTY Bandsaw 2 HP 143 Wearing Proper APPAREL. 9d cdi lZVg SafetySafety Instructions for Machinery Children & BYSTANDERS. @ZZe XaYgZc MAINTENANCE/SERVICE.  6aa cheZXidch! Additional Safety for BandsawsBlade Replacement SAFETY. 7ZhYZhYh Circuit Requirements Power Supply Circuit RequirementsPower Connection Device Full Load Amperage DrawUnpacking SetupNeeded for Setup Description QtyHardware and Tools not shown Qty InventoryBox 1 Figures Qty Hardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadBolting to Concrete Floors Moving & Placing Base UnitMounting to Shop Floor Guide Post Handwheel To install the guide post handwheelTo install the table To adjust the blade tracking Blade TrackingTo set up the positive stop Positive StopTo assemble the fence Dust Collection Fence AssemblyTo connect a dust collection hose To adjust the miter slot square to the blade Fence AdjustmentTo adjust the fence parallel to the miter slot Table AlignmentTo tension the bandsaw blade Test Run Tensioning BladeTo test run the machine To adjust the upper blade guide Blade GuidesFront of lower blade guide Page Straight Cuts OperationsOverview Irregular CutsSTART/STOP Switch Guide Post To adjust guide postTo tilt the table Fine Tune TrackingTable Tilt To make a 90˚ crosscut RippingCrosscuttingTo make a rip cut To make a resaw cut ResawingCutting Curves To complete a stacked cut To adjust the blade speedStacked Cuts Blade Speed Blade Width Blade InformationBlade Length Blade Care Tooth StyleTooth Pitch Blade BreakageTo remove a blade Blade ChangesMost common causes of blade breakage are To replace a bladeAccessories T10117 Big Mouth Dust Hood Schedule MaintenanceCleaning Unpainted Cast IronTo remove and clean the bearings LubricationService TroubleshootingOnly cut wood and ensure moisture is below 20% Make tight inside cuts Symptom Possible Cause Possible Solution To check the V-belt Checking V-BeltTensioning V-Belt Tools Needed QtyReplacing V-Belt To replace the V-beltTo adjust the tension lever, do these steps Adjusting Tension LeverAdjusting Wheel Brush To adjust the wheel brushTo skew your fence Blade LeadTo correct blade lead To shift the tableComponents and Hardware Needed Qty Aligning WheelsChecking Coplanarity Tools NeededShimming Upper Wheel 8deaVcVg Cdi8deaVcVgTo adjust the lower wheel Adjusting Lower WheelAdjusting Guide Post Travel ⁄4 turn 7gVX`Zi Hb6 JYZ Wiring Wiring Safety InstructionsKdY&%ZlgZ&iG G0513/G0514 Wiring DiagramHLI8= Main Main Parts List DescriptionPLW04M Lock Washer 8MM PW01M Flat Washer 8MM PB14M Fence Blade Guide Blade Guide Parts List Label Placement DescriptionWarranty Card 10. 8dbbZcih99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns Page Order Hours a DAY

G0514 specifications

The Grizzly G0514 is a top-tier bandsaw designed specifically for serious woodworkers and industrial applications. This machine is celebrated for its powerful cutting capabilities and precision, making it a vital tool for anyone looking to handle large projects with ease.

One of the standout features of the Grizzly G0514 is its robust 2 HP, 220V motor that provides ample power for cutting through thick hardwoods, softwoods, and even non-ferrous metals. This strong motor ensures a stable performance, enabling users to tackle various cutting tasks without worrying about overheating or stalling. Complementing this motor is a dual voltage capability, allowing users to switch between 120V and 220V power sources, making it incredibly versatile for different workshops.

The Grizzly G0514 also boasts a large 17-inch throat capacity, which translates to an impressive resaw height of 12 inches. This means that woodworkers can rip large pieces of timber or veneer with remarkable ease. The 14-inch blade length further enhances its cutting capabilities, providing smooth and clean cuts every time.

Another significant characteristic of this bandsaw is the precision-bearing blade guides. These guides ensure that the blade remains stable during operation, reducing blade deflection and enhancing the quality of cuts. The G0514 is equipped with a heavy-duty cast iron frame and base, which not only ensures stability and durability but also helps minimize vibrations—giving users a smoother cutting experience.

Featuring a rich array of technologies, the Grizzly G0514 is built with user-friendliness in mind. The quick-release blade tension lever allows for speedy adjustments when switching blades, maximizing efficiency. Additionally, it comes with a full-size table measuring 22 inches by 27 inches, providing ample workspace for larger projects.

Safety is paramount in woodworking, and this bandsaw is no exception, featuring a blade brake and an integrated dust port that helps maintain a clean work environment. The G0514 also comes equipped with a fence and miter gauge, enabling accurate cuts and angled woodworking tasks.

In summary, the Grizzly G0514 is an excellent choice for both professional woodworkers and hobbyists alike. With its powerful motor, vast cutting capacity, and user-friendly features, it stands out as a reliable and high-performance bandsaw in the market. Whether you’re crafting intricate furniture or simply doing home projects, the G0514 is designed to meet all your woodworking needs efficiently and safely.