Grizzly G0514 owner manual Machine Data Sheet

Page 7

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL G0513 17" BANDSAW - 2 HP

Product Dimensions:
Weight	266 lbs.
Length/Width/Height	32 x 32 x 73 in.
Foot Print (Length/Width)	27 x 17-3/4 in.
Shipping Dimensions:
Type	Wood Slat Crate
Content	Machine
Weight	342 lbs.
Length/Width/Height	20 x 30 x 81 in.
Electrical:
Power Requirement	110V or 220V, Single-Phase, 60 Hz
Minimum Circuit Size	30 amps at 110V, 15 amps at 220V
Switch	On/Off Push Button
Switch Voltage	110/220V
Cord Length	6 ft.
Cord Gauge	14 gauge
Plug Included	No
Recommended Plug/Outlet Type	L5-30 at 110V, 6-15 at 220V
Motors:
Main
Type	TEFC Capacitor Start Induction
Horsepower	2 HP
Voltage	110/220V
Prewired	220V
Phase	Single
Amps	20/10A
Speed	1725 RPM
Cycle	60 Hz
Number Of Speeds	1
Power Transfer	Belt Drive
Bearings	Shielded and Permanently Lubricated
Main Specifications:
Operation
Blade Speeds	1700, 3500 FPM
Table Tilt	Left 10, Right 45 deg.
Cutting Capacities
Maximum Cutting Height	12-1/8 in.
Max Capacity Under Handwheel	12 in.
Max Capacity Left of Blade	16-1/4 in.

Model G0513/G0514 (Mfg. since 8/02+)

-5-

Image 7

Contents

Model G0513/G0514 17 & 19 Heavy Duty Bandsaws Ss ,EAD from Leadbased PAINTS Table of Contents Machine Description IntroductionManual Accuracy Contact InfoIdentification Blade Tension Scale Tension Lever Adjustment ScrewWheel Brush Machine Data Sheet Table Information Model G0514 19 HEAVY-DUTY Bandsaw 2 HP 143 Safety Instructions for Machinery SafetyWearing Proper APPAREL. 9d cdi lZVg Children & BYSTANDERS. @ZZe XaYgZc Blade Replacement SAFETY. 7ZhYZhYh Additional Safety for BandsawsMAINTENANCE/SERVICE. 6aa cheZXidch! Full Load Amperage Draw Power Supply Circuit RequirementsPower Connection Device Circuit RequirementsDescription Qty SetupNeeded for Setup UnpackingBox 1 Figures Qty InventoryHardware and Tools not shown Qty Hardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsMounting to Shop Floor Moving & Placing Base UnitBolting to Concrete Floors To install the table To install the guide post handwheelGuide Post Handwheel Blade Tracking To adjust the blade trackingPositive Stop To set up the positive stopTo connect a dust collection hose Dust Collection Fence AssemblyTo assemble the fence Table Alignment Fence AdjustmentTo adjust the fence parallel to the miter slot To adjust the miter slot square to the bladeTo test run the machine Test Run Tensioning BladeTo tension the bandsaw blade Blade Guides To adjust the upper blade guideFront of lower blade guide Page Irregular Cuts OperationsOverview Straight CutsTo adjust guide post START/STOP Switch Guide PostTable Tilt Fine Tune TrackingTo tilt the table To make a rip cut RippingCrosscuttingTo make a 90˚ crosscut Cutting Curves ResawingTo make a resaw cut Stacked Cuts Blade Speed To adjust the blade speedTo complete a stacked cut Blade Length Blade InformationBlade Width Blade Breakage Tooth StyleTooth Pitch Blade CareTo replace a blade Blade ChangesMost common causes of blade breakage are To remove a bladeAccessories T10117 Big Mouth Dust Hood Unpainted Cast Iron MaintenanceCleaning ScheduleLubrication To remove and clean the bearingsTroubleshooting ServiceOnly cut wood and ensure moisture is below 20% Make tight inside cuts Symptom Possible Cause Possible Solution Tools Needed Qty Checking V-BeltTensioning V-Belt To check the V-beltTo replace the V-belt Replacing V-BeltTo adjust the wheel brush Adjusting Tension LeverAdjusting Wheel Brush To adjust the tension lever, do these stepsTo shift the table Blade LeadTo correct blade lead To skew your fenceTools Needed Aligning WheelsChecking Coplanarity Components and Hardware Needed Qty8deaVcVg Cdi8deaVcVg Shimming Upper WheelAdjusting Guide Post Travel Adjusting Lower WheelTo adjust the lower wheel ⁄4 turn 7gVX`Zi Hb6 JYZ Wiring Safety Instructions WiringHLI8= G0513/G0514 Wiring DiagramKdY&%ZlgZ&iG Main Description Main Parts ListPLW04M Lock Washer 8MM PW01M Flat Washer 8MM PB14M Fence Blade Guide Blade Guide Parts List Description Label Placement10. 8dbbZcih Warranty Card99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns Page Order Hours a DAY