Woodstock W1701 owner manual Test Run

Page 14

W1701 1HP Shaper

8. For custom fence facing, make sure the screw heads

 

 

 

 

 

 

 

 

 

 

 

Safety

 

Safety

 

are countersunk completely below the surface of the

 

 

 

 

Guard

 

Guard Bar

 

fence face.

 

 

 

 

 

 

 

 

 

 

 

 

 

9.Connect the safety guard bar to the safety guard shaft with two M8-1.25 x 12 bolts and the 8mm flat

washers. See Figure 12.

10. Connect the safety guard to the safety guard bar

 

 

 

 

 

 

 

 

 

 

 

 

Fence

 

 

 

 

 

 

 

 

 

 

 

 

Safety Guard

 

 

with two M4-0.7 x 12 Phillips® head screws and the

 

 

Housing

 

 

 

 

 

 

 

 

 

 

Shaft

 

 

M4-0.7 nuts. See Figure 12.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11. Position the extension bar and safety guard on the

 

 

Figure 12. Guard and fence assembly.

 

 

 

 

 

 

 

 

 

 

main fence housing and install the T-lock handle.

 

 

 

 

 

 

 

 

 

 

See Figure 12.

 

 

 

 

 

 

 

 

 

 

 

 

Hold Spindle

 

 

 

 

 

 

 

 

 

 

12. Position the guard as close as possible to the spin-

 

 

Here

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

dle/cutter without impeding the feeding path of the

 

 

 

 

 

 

 

 

 

 

workpiece.

 

 

 

 

 

 

 

 

 

 

13. Place an 8mm open-end wrench on top the spindle

 

 

 

 

 

 

 

 

 

 

(see Figure 13).

 

 

 

 

 

 

 

 

 

 

14. Using a 14mm open-end wrench on the drawbar nut,

 

 

 

 

 

 

 

 

 

 

(Figure 14), make sure the drawbar nut is tight, but

 

 

 

 

 

 

 

 

 

 

DO NOT over-tighten the drawbar nut.

 

 

Figure 13. Wrench location on spindle.

Note: This is an important safety measure that

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

must be done before the Test Run on the next

 

 

 

 

 

 

 

 

 

 

page.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Test Run

 

 

 

 

 

 

Taper

 

 

 

 

 

 

 

 

 

 

 

 

Complete this process once you have familiarized yourself

 

 

 

 

 

 

 

 

 

 

with all instructions in this manual.

 

 

 

 

 

 

 

 

 

 

To test run the shaper, do these steps:

 

 

 

 

 

 

 

 

 

 

1. Read the entire instruction manual first, so you

 

 

 

 

 

 

 

Figure 14. Threading on drawbar nut with

are familiar with all controls and functions of the

 

 

 

 

the tapered end up.

shaper!

 

 

 

 

 

 

 

 

 

 

2. Connect your machine to the power source.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3. Turn the shaper ON. The shaper should run smoothly

 

 

 

 

 

 

 

 

 

 

with little or no vibration.

 

 

 

 

 

 

 

 

 

 

— Immediately turn the jointer OFF if you suspect

 

 

 

 

 

 

 

 

 

 

any problems, and fix those problems before start-

 

 

 

 

 

 

 

 

 

 

ing the shaper again. If the source of an unusual

 

 

Projectiles thrown from the machine

 

noise or vibration is not readily apparent, contact

 

 

could cause serious eye injury. Wear

our technical support for help at (360) 734-3482 or

 

 

safety glasses during the test run!

contact us online at tech-support@shopfox.biz.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-11-

 

 

 

 

 

 

 

 

 

 

SET UP

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Copyright FEBRUARY, 2008 by Woodstock INTERNATIONAL, INC Model W1701PART# Description HP Shaper Page Contents Woodstock Technical Support SpecificationsIntroduction Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Shapers Avoiding Potential Injuries Use a Shop FOX Featherboard as Anti-kick back protectionExtension Cords Electrical110V Operation GroundingInventory SET UPUnpacking Lifting HazardMain Contents Qty Machine PlacementCleaning Machine Inventory ListAssembly Laceration HazardTest Run Cutters vs. Router Bits OperationsGeneral To set the spindle height, do these steps Spindle ElevationSpindle Direction Cutter Contact HazardTable Inserts Fence PositioningFence Alignment Accidental START-UP Hazard Cutter InstallationThere are three set up positions for rub collars Cutter FLY-APART HazardTo install cutters and rub collars, do these steps AMPUTATION/LACERATION HazardRouter Bit Installation To install the router bit collet, do these stepsTo set up the fence for partial edge removal, do these steps Straight ShapingTemplates Template Construction TipsFreehand Shaping Starting pin operation Guard not shown for clarityTable & Base MaintenanceMaintenance Schedule LubricationTo adjust belt, do these steps ServiceBelt Adjustment Loosen the belt adjustment bolts as shown in FigureTo install the table spacer kit, do these steps Table Spacer KitSpindle Cartridge Replacement To replace the spindle cartridge assemblyResurfacing a shaper fence on a Jointer Electrical Components & Wiring ON/OFF Switch Motor & FWD/REV SwitchParts Parts List PART# DescriptionCutterspindle Warranty Warranty Registration CommentsWoodstock International INC BOX BELLINGHAM, WA
Top Page Image Contents