Woodstock W1824 manual Unpacking, Needed for Setup, Description Qty

Page 15

Df[\cN(/)+('?pYi`[KXYc\JXn

SETUP

Unpacking

This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately.

Needed for Setup

The following are needed to complete the setup process, but are not included with the machine:

Description		Qty
• Safety Glasses for Each Person		1
• Degreaser or Solvent for Cleaning		Varies
•	Rags for Cleaning	Varies
•	Straightedge	1
•	Level	1
•	Dust Collection System	1
•	4" Dust Hose	1
•	4" Hose Clamp	1
• Another Person for Lifting		1
•	Needle Nose Pliers	1
• Wrench or Socket 17mm		1
• Wrench or Socket 14mm		1
• Wrench or Socket 10mm		1
•	Adjustable Wrench	1

B\\g dXZ_`e\ [`jZfee\Zk\[ ]ifd gfn\ilek`c`ejkilZk\[fk_\in`j\%

The Model W1824 is a heavy machine. Serious personal injury may occur if safe moving methods are not used. To be safe, get assistance and use power equipment to move the shipping crate and machine.

J<KLG

-13-

Image 15

Contents DLCGHB6CJ6A Page Fek\ekj Controls and Features IntroductionWoodstock Technical Support @EKIFLK@FE @EKIFLK@FE @EKIFLK@FE For Your Own Safety Read Manual Before Operating Machine SafetyJ8=KP Additional Safety for Table Saws Kickback Avoiding KickbackProtecting Yourself from Kickback Full-Load Current Rating Circuit Requirements for 220V PrewiredElectrical Circuit RequirementsExtension Cords For 220V Connection PrewiredFor 110V Connection Must be Rewired Grounding RequirementsItems Needed Voltage ConversionDescription Qty SetupNeeded for Setup UnpackingInventory Shipping Inventory Figures QtyHardware Not Shown Qty Cleaning Machine Machine PlacementTo assemble the table saw, do these steps AssemblyMasking tape location for Shimming the wing up Slots before fully tightening the fasteners Fence rail tube attached To connect a dust hose to the table saw, do these Steps Dust CollectionTo test run the machine, do these steps Recommended AdjustmentsAdjustments that should be verified Test RunOperations GeneralBasic Controls Operation Overview Workpiece Inspection Non-Through & Through Cuts Non-Through CutsThrough Cuts Blade Selection Blade Size RequirementsDado Blades Laminate Blade Features FigureTo install the blade, do these steps Blade InstallationSpreader Blade Guard AssemblyBlade Guard & Spreader Installation GuardAnti-Kickback Pawls Blade guard and spreader Properly installedWhen to Use the Blade Guard When Not to Use the Blade GuardTo disable the pawls, do these steps Riving Knife Installation When to Use the Riving KnifeRiving Knife Example photo of a ripping Operation RippingCrosscutting To make a crosscut using the miter gauge, do these stepsMiter Cuts Blade Tilt CutsTo perform a miter cut, do these steps Dado Blade Installation Dado CuttingCutting Dados with a Dado Blade To cut a dado with a dado blade, do these steps To use a standard saw blade to cut dadoes, do these steps Cutting Dados with a Standard BladeCutting Rabbets with a Dado Blade Rabbet CuttingTo cut rabbets with the standard blade, do these steps Cutting Rabbets with a Standard BladeComponents Needed for Resaw Barrier ResawingMaking a Resaw Barrier Tools Needed QtyTools Needed for the Auxiliary Fence Auxiliary FenceTo build the resaw barrier, do these steps Components Needed for the Auxiliary FenceResawing Operation Components Needed for ResawingTo perform resawing operations, do these steps Completed resaw operation SHOP-MADE Safety Accessories FeatherboardsMaking a Featherboard Patterns for featherboard miter Bar Proceed to Mounting Featherboard in Miter Slot on the nextMounting Featherboard in Miter Slot Mounting Featherboard with ClampsMaking a Push Stick Push SticksMaking a Push Block Push BlocksMaking a Narrow-Rip Push Block for an Auxiliary Fence Material Needed for Narrow Rip Auxiliary Fence & Push BlockMaterial Needed for Push Block Adjusted distance between Blade and auxiliary fence Using the Auxiliary Fence and Push BlockCrosscut Sled Outfeed & Support TablesW1727-1 HP Dust Collector AccessoriesTable Saw Accessories D2057-Heavy-Duty Mobile BaseD3096-Shop Fox Featherboard W1104-Yellow Board Buddy PairW1105-Green Board Buddy Pair W1104-Orange Board Buddy PairMaintenance CleaningSchedule Lubrication Trunnion SlidesWorm Gear, Bull Gear & Leadscrew Service Belt ServiceTensioning Belt Replacing Belt Check for proper belt tension Close the motor access coverTilt Stop Collars Setting 90 Stop CollarSetting 45 Stop Collar Step B Miter Slot to Blade ParallelismLocation of the front trunnion Cap screw 1 Locations of the front trunnion Shims Blade tilted to Straightedge Proceed to Adjusting Bent Spreader/Riving KnifeSpreader or Riving Knife Alignment Checking Alignment with BladeAdjusting Bent Spreader/Riving Knife Adjusting AlignmentHeight and Squareness Fence AdjustmentsParallelism & Clamping Pressure below Parallelism & Clamping PressureAligning the fence to Miter slot Optional Offset Fence AdjustmentMiter Gauge Adjustments Checking/Setting 90 StopsChecking/Setting 45 Stops Wiring Diagram Color KEY Electrical Safety Instructions110 VAC Plug As Recommended VAC 6-20 Plug110V/220V Motor capacitor location Electrical ComponentsGIF9CD TroubleshootingG8IKJ Cabinet & Table PartsTrunnion & Switch Breakdown Description Trunnion & Switch Parts ListBlade Guard Fence/Rails/Miter Gauge Breakdown Fence/Rails/Miter Gauge Parts List Fence Label Label PlacementPage Page Page Place Stamp Here N8II8EKP =\FjVainBVXcZhVcYIddah