Woodstock W1824 manual To cut a dado with a dado blade, do these steps

Page 38

Df[\cN(/)+('?pYi`[KXYc\JXn

To cut a dado with a dado blade, do these steps:

1.DISCONNECT SAW FROM POWER!

2.Adjust the dado blade to the desired depth of cut.

3.Adjust the distance between the fence and the inside edge of the blade, as shown in Figure 51 on the previous page, to dado the length of a workpiece.

If dadoing across the workpiece, use the miter gauge and carefully line up the desired cut with the dado blade. DO NOT use the fence in combination with the miter gauge, which could result in the workpiece binding and kicking back.

4.Re-connect the saw to the power source.

5.Turn the saw ON. The blade should run smooth, with no vibrations.

6.When the blade has reached full speed, perform a test cut with a scrap piece of wood.

7.If the cut is satisfactory, repeat the cut with the actual workpiece.

FG<I8K@FEJ

;X[f9cX[\

=\eZ\

Nfibg`\Z\

Figure 51. Illustration of a dado cut.

-36-

Image 38
Contents DLCGHB6CJ6A Page Fek\ekj Woodstock Technical Support Controls and FeaturesIntroduction @EKIFLK@FE @EKIFLK@FE @EKIFLK@FE Safety For Your Own Safety Read Manual Before Operating MachineJ8=KP Additional Safety for Table Saws Protecting Yourself from Kickback KickbackAvoiding Kickback Circuit Requirements Circuit Requirements for 220V PrewiredElectrical Full-Load Current RatingGrounding Requirements For 220V Connection PrewiredFor 110V Connection Must be Rewired Extension CordsVoltage Conversion Items NeededUnpacking SetupNeeded for Setup Description QtyHardware Not Shown Qty InventoryShipping Inventory Figures Qty Machine Placement Cleaning MachineAssembly To assemble the table saw, do these stepsMasking tape location for Shimming the wing up Slots before fully tightening the fasteners Fence rail tube attached Dust Collection To connect a dust hose to the table saw, do these StepsTest Run Recommended AdjustmentsAdjustments that should be verified To test run the machine, do these stepsBasic Controls OperationsGeneral Operation Overview Workpiece Inspection Through Cuts Non-Through & Through CutsNon-Through Cuts Blade Size Requirements Blade SelectionLaminate Blade Features Figure Dado BladesBlade Installation To install the blade, do these stepsGuard Blade Guard AssemblyBlade Guard & Spreader Installation SpreaderBlade guard and spreader Properly installed Anti-Kickback PawlsTo disable the pawls, do these steps When to Use the Blade GuardWhen Not to Use the Blade Guard Riving Knife Riving Knife InstallationWhen to Use the Riving Knife Ripping Example photo of a ripping OperationTo make a crosscut using the miter gauge, do these steps CrosscuttingTo perform a miter cut, do these steps Miter CutsBlade Tilt Cuts Cutting Dados with a Dado Blade Dado Blade InstallationDado Cutting To cut a dado with a dado blade, do these steps Cutting Dados with a Standard Blade To use a standard saw blade to cut dadoes, do these stepsRabbet Cutting Cutting Rabbets with a Dado BladeCutting Rabbets with a Standard Blade To cut rabbets with the standard blade, do these stepsTools Needed Qty ResawingMaking a Resaw Barrier Components Needed for Resaw BarrierComponents Needed for the Auxiliary Fence Auxiliary FenceTo build the resaw barrier, do these steps Tools Needed for the Auxiliary FenceTo perform resawing operations, do these steps Resawing OperationComponents Needed for Resawing Completed resaw operation Making a Featherboard SHOP-MADE Safety AccessoriesFeatherboards Proceed to Mounting Featherboard in Miter Slot on the next Patterns for featherboard miter BarMounting Featherboard with Clamps Mounting Featherboard in Miter SlotPush Sticks Making a Push StickPush Blocks Making a Push BlockMaterial Needed for Push Block Making a Narrow-Rip Push Block for an Auxiliary FenceMaterial Needed for Narrow Rip Auxiliary Fence & Push Block Using the Auxiliary Fence and Push Block Adjusted distance between Blade and auxiliary fenceOutfeed & Support Tables Crosscut SledD2057-Heavy-Duty Mobile Base AccessoriesTable Saw Accessories W1727-1 HP Dust CollectorW1104-Orange Board Buddy Pair W1104-Yellow Board Buddy PairW1105-Green Board Buddy Pair D3096-Shop Fox FeatherboardSchedule MaintenanceCleaning Worm Gear, Bull Gear & Leadscrew LubricationTrunnion Slides Tensioning Belt ServiceBelt Service Check for proper belt tension Close the motor access cover Replacing BeltSetting 90 Stop Collar Tilt Stop CollarsSetting 45 Stop Collar Miter Slot to Blade Parallelism Step BLocation of the front trunnion Cap screw 1 Locations of the front trunnion Shims Blade tilted to Checking Alignment with Blade Proceed to Adjusting Bent Spreader/Riving KnifeSpreader or Riving Knife Alignment StraightedgeAdjusting Alignment Adjusting Bent Spreader/Riving KnifeFence Adjustments Height and SquarenessParallelism & Clamping Pressure Parallelism & Clamping Pressure belowOptional Offset Fence Adjustment Aligning the fence to Miter slotChecking/Setting 45 Stops Miter Gauge AdjustmentsChecking/Setting 90 Stops Electrical Safety Instructions Wiring Diagram Color KEY110V/220V 110 VAC Plug As RecommendedVAC 6-20 Plug Electrical Components Motor capacitor locationTroubleshooting GIF9CDG8IKJ Parts Cabinet & TableTrunnion & Switch Breakdown Trunnion & Switch Parts List DescriptionBlade Guard Fence/Rails/Miter Gauge Breakdown Fence/Rails/Miter Gauge Parts List Label Placement Fence LabelPage Page Page Place Stamp Here N8II8EKP =\FjVainBVXcZhVcYIddah