Woodstock W1824 manual W1104-Yellow Board Buddy Pair, W1105-Green Board Buddy Pair

Page 55

Df[\cN(/)+('?pYi`[KXYc\JXn

W1104—Yellow Board Buddy® Pair

Feature clockwise turning wheels to maintain constant, even feeding pressure. If a kickback occurs, the wheels lock up and function as anti- kickback devices.

W1105—Green Board Buddy® Pair

Feature wheels that turn in both directions to function as bidirectional hold-downs.

W1104—Orange Board Buddy® Pair

Feature counterclockwise turning wheels to maintain constant, even feeding pressure. If a kickback occurs, the wheels lock up and function as anti-kickback devices.

D3096—Shop Fox Featherboard

Reduce the risk of kickback and achieve consistent feeding results with these Shop Fox featherboards. Fits standard 3⁄8" x 3⁄4" miter gauge slots.

D3122—Shop Fox Push Stick

This essential safety item keeps hands at a safe distance from blades and cutters while still maintaining control of the workpiece against machine fences. A true necessity when running narrow stock. The durable handle is designed for maximum control. Measures 131⁄2" overall. Super ergonomic design!

D3119—Board Straighteners™

These Board Straighteners™ allow a board with a curved or crooked edge to attach to a board with a known straight edge. This stable arrangement can then be used against a table saw fence, which in turn transfers a straight-line cut to the crooked board. Board Straighteners™ allow cutting a straight edge on boards that would otherwise be too dangerous to rip unaided.

D3096

D3122

D8@EK<E8E:<

-53-

Image 55

Contents DLCGHB6CJ6A Page Fek\ekj Introduction Controls and FeaturesWoodstock Technical Support @EKIFLK@FE @EKIFLK@FE @EKIFLK@FE For Your Own Safety Read Manual Before Operating Machine SafetyJ8=KP Additional Safety for Table Saws Avoiding Kickback KickbackProtecting Yourself from Kickback Full-Load Current Rating Circuit Requirements for 220V PrewiredElectrical Circuit RequirementsExtension Cords For 220V Connection PrewiredFor 110V Connection Must be Rewired Grounding RequirementsItems Needed Voltage ConversionDescription Qty SetupNeeded for Setup UnpackingShipping Inventory Figures Qty InventoryHardware Not Shown Qty Cleaning Machine Machine PlacementTo assemble the table saw, do these steps AssemblyMasking tape location for Shimming the wing up Slots before fully tightening the fasteners Fence rail tube attached To connect a dust hose to the table saw, do these Steps Dust CollectionTo test run the machine, do these steps Recommended AdjustmentsAdjustments that should be verified Test RunGeneral OperationsBasic Controls Operation Overview Workpiece Inspection Non-Through Cuts Non-Through & Through CutsThrough Cuts Blade Selection Blade Size RequirementsDado Blades Laminate Blade Features FigureTo install the blade, do these steps Blade InstallationSpreader Blade Guard AssemblyBlade Guard & Spreader Installation GuardAnti-Kickback Pawls Blade guard and spreader Properly installedWhen Not to Use the Blade Guard When to Use the Blade GuardTo disable the pawls, do these steps When to Use the Riving Knife Riving Knife InstallationRiving Knife Example photo of a ripping Operation RippingCrosscutting To make a crosscut using the miter gauge, do these stepsBlade Tilt Cuts Miter CutsTo perform a miter cut, do these steps Dado Cutting Dado Blade InstallationCutting Dados with a Dado Blade To cut a dado with a dado blade, do these steps To use a standard saw blade to cut dadoes, do these steps Cutting Dados with a Standard BladeCutting Rabbets with a Dado Blade Rabbet CuttingTo cut rabbets with the standard blade, do these steps Cutting Rabbets with a Standard BladeComponents Needed for Resaw Barrier ResawingMaking a Resaw Barrier Tools Needed QtyTools Needed for the Auxiliary Fence Auxiliary FenceTo build the resaw barrier, do these steps Components Needed for the Auxiliary FenceComponents Needed for Resawing Resawing OperationTo perform resawing operations, do these steps Completed resaw operation Featherboards SHOP-MADE Safety AccessoriesMaking a Featherboard Patterns for featherboard miter Bar Proceed to Mounting Featherboard in Miter Slot on the nextMounting Featherboard in Miter Slot Mounting Featherboard with ClampsMaking a Push Stick Push SticksMaking a Push Block Push BlocksMaterial Needed for Narrow Rip Auxiliary Fence & Push Block Making a Narrow-Rip Push Block for an Auxiliary FenceMaterial Needed for Push Block Adjusted distance between Blade and auxiliary fence Using the Auxiliary Fence and Push BlockCrosscut Sled Outfeed & Support TablesW1727-1 HP Dust Collector AccessoriesTable Saw Accessories D2057-Heavy-Duty Mobile BaseD3096-Shop Fox Featherboard W1104-Yellow Board Buddy PairW1105-Green Board Buddy Pair W1104-Orange Board Buddy PairCleaning MaintenanceSchedule Trunnion Slides LubricationWorm Gear, Bull Gear & Leadscrew Belt Service ServiceTensioning Belt Replacing Belt Check for proper belt tension Close the motor access coverTilt Stop Collars Setting 90 Stop CollarSetting 45 Stop Collar Step B Miter Slot to Blade ParallelismLocation of the front trunnion Cap screw 1 Locations of the front trunnion Shims Blade tilted to Straightedge Proceed to Adjusting Bent Spreader/Riving KnifeSpreader or Riving Knife Alignment Checking Alignment with BladeAdjusting Bent Spreader/Riving Knife Adjusting AlignmentHeight and Squareness Fence AdjustmentsParallelism & Clamping Pressure below Parallelism & Clamping PressureAligning the fence to Miter slot Optional Offset Fence AdjustmentChecking/Setting 90 Stops Miter Gauge AdjustmentsChecking/Setting 45 Stops Wiring Diagram Color KEY Electrical Safety InstructionsVAC 6-20 Plug 110 VAC Plug As Recommended110V/220V Motor capacitor location Electrical ComponentsGIF9CD TroubleshootingG8IKJ Cabinet & Table PartsTrunnion & Switch Breakdown Description Trunnion & Switch Parts ListBlade Guard Fence/Rails/Miter Gauge Breakdown Fence/Rails/Miter Gauge Parts List Fence Label Label PlacementPage Page Page Place Stamp Here N8II8EKP =\FjVainBVXcZhVcYIddah