Woodstock W1824 manual G8IKJ

Page 75

Df[\cN(/)+('?pYi`[KXYc\JXn

GIF9C<D		GFJJ@9C<:8LJ<		:FII<:K@M<8:K@FE
Blade is not aligned with	1.	Blade is warped.	1.	Replace blade (see Page 27).
miter slot or fence.	2.	Table top is not parallel to blade.	2.	Make miter slot parallel to blade (see Page 60).
	3.	Fence is not parallel to blade.	3.	Make fence parallel to blade (see Page 66).
Blade does not reach 90°.	1.	90° stop collar is out of adjust-	1.	Adjust 90° stop collar (see Page 58).
		ment.
	2.	Sawdust stuck on stop collar.	2.	Clean sawdust off stop collar.
Blade hits insert at 45°.	1.	45° stop collar is out of adjust-	1.	Adjust 45° stop collar (see Page 59).
		ment.
	2.	Sawdust stuck on stop collar.	2.	Clean sawdust off stop collar.
	3.	Slot in insert is inadequate.	3.	File or mill the slot in the insert.
	4.	Table out of alignment.	4.	Align miter slot to the blade (see Page 60).
	5.	Blade position is incorrect.	5.	Adjust blade position.
Board binds or burns when	1.	Dull blade.	1.	Replace blade (see Page 27).
feeding through table saw.	2.	Blade is warped.	2.	Replace blade (see Page 27).
	3.	Fence is not parallel to blade.	3.	Make fence parallel to blade (see Page 65).
	4.	Table top is not parallel to blade.	4.	Make miter slot parallel to blade (see Page 60).

G8IKJ

-73-

Image 75

Contents DLCGHB6CJ6A Page Fek\ekj Controls and Features IntroductionWoodstock Technical Support @EKIFLK@FE @EKIFLK@FE @EKIFLK@FE For Your Own Safety Read Manual Before Operating Machine SafetyJ8=KP Additional Safety for Table Saws Kickback Avoiding KickbackProtecting Yourself from Kickback Full-Load Current Rating Circuit Requirements for 220V PrewiredElectrical Circuit RequirementsExtension Cords For 220V Connection PrewiredFor 110V Connection Must be Rewired Grounding RequirementsItems Needed Voltage ConversionDescription Qty SetupNeeded for Setup UnpackingInventory Shipping Inventory Figures QtyHardware Not Shown Qty Cleaning Machine Machine PlacementTo assemble the table saw, do these steps AssemblyMasking tape location for Shimming the wing up Slots before fully tightening the fasteners Fence rail tube attached To connect a dust hose to the table saw, do these Steps Dust CollectionTo test run the machine, do these steps Recommended AdjustmentsAdjustments that should be verified Test RunOperations GeneralBasic Controls Operation Overview Workpiece Inspection Non-Through & Through Cuts Non-Through CutsThrough Cuts Blade Selection Blade Size RequirementsDado Blades Laminate Blade Features FigureTo install the blade, do these steps Blade InstallationSpreader Blade Guard AssemblyBlade Guard & Spreader Installation GuardAnti-Kickback Pawls Blade guard and spreader Properly installedWhen to Use the Blade Guard When Not to Use the Blade GuardTo disable the pawls, do these steps Riving Knife Installation When to Use the Riving KnifeRiving Knife Example photo of a ripping Operation RippingCrosscutting To make a crosscut using the miter gauge, do these stepsMiter Cuts Blade Tilt CutsTo perform a miter cut, do these steps Dado Blade Installation Dado CuttingCutting Dados with a Dado Blade To cut a dado with a dado blade, do these steps To use a standard saw blade to cut dadoes, do these steps Cutting Dados with a Standard BladeCutting Rabbets with a Dado Blade Rabbet CuttingTo cut rabbets with the standard blade, do these steps Cutting Rabbets with a Standard BladeComponents Needed for Resaw Barrier ResawingMaking a Resaw Barrier Tools Needed QtyTools Needed for the Auxiliary Fence Auxiliary FenceTo build the resaw barrier, do these steps Components Needed for the Auxiliary FenceResawing Operation Components Needed for ResawingTo perform resawing operations, do these steps Completed resaw operation SHOP-MADE Safety Accessories FeatherboardsMaking a Featherboard Patterns for featherboard miter Bar Proceed to Mounting Featherboard in Miter Slot on the nextMounting Featherboard in Miter Slot Mounting Featherboard with ClampsMaking a Push Stick Push SticksMaking a Push Block Push BlocksMaking a Narrow-Rip Push Block for an Auxiliary Fence Material Needed for Narrow Rip Auxiliary Fence & Push BlockMaterial Needed for Push Block Adjusted distance between Blade and auxiliary fence Using the Auxiliary Fence and Push BlockCrosscut Sled Outfeed & Support TablesW1727-1 HP Dust Collector AccessoriesTable Saw Accessories D2057-Heavy-Duty Mobile BaseD3096-Shop Fox Featherboard W1104-Yellow Board Buddy PairW1105-Green Board Buddy Pair W1104-Orange Board Buddy PairMaintenance CleaningSchedule Lubrication Trunnion SlidesWorm Gear, Bull Gear & Leadscrew Service Belt ServiceTensioning Belt Replacing Belt Check for proper belt tension Close the motor access coverTilt Stop Collars Setting 90 Stop CollarSetting 45 Stop Collar Step B Miter Slot to Blade ParallelismLocation of the front trunnion Cap screw 1 Locations of the front trunnion Shims Blade tilted to Straightedge Proceed to Adjusting Bent Spreader/Riving KnifeSpreader or Riving Knife Alignment Checking Alignment with BladeAdjusting Bent Spreader/Riving Knife Adjusting AlignmentHeight and Squareness Fence AdjustmentsParallelism & Clamping Pressure below Parallelism & Clamping PressureAligning the fence to Miter slot Optional Offset Fence AdjustmentMiter Gauge Adjustments Checking/Setting 90 StopsChecking/Setting 45 Stops Wiring Diagram Color KEY Electrical Safety Instructions110 VAC Plug As Recommended VAC 6-20 Plug110V/220V Motor capacitor location Electrical ComponentsGIF9CD TroubleshootingG8IKJ Cabinet & Table PartsTrunnion & Switch Breakdown Description Trunnion & Switch Parts ListBlade Guard Fence/Rails/Miter Gauge Breakdown Fence/Rails/Miter Gauge Parts List Fence Label Label PlacementPage Page Page Place Stamp Here N8II8EKP =\FjVainBVXcZhVcYIddah