Emerson SZO56, SZO44, SZV44, SZV32 Fire and Explosion Hazards, Reactivity Data, Health Hazard Data

Page 39

Dual-Compressor ModuleMaterial Data Safety Sheet

A.6 Fire and Explosion Hazards

Flash Point (by Cleveland Open

320-530°F (160-276°C)

Cup)

 

 

 

Flammable Limits

 

Not established

Auto-Ignition Temperature

No data

HMIS Ratings

 

Health

0

 

Flammability

1

 

 

Reactivity

0

NFPA Ratings

 

Not established

Extinguishing Media

 

Dry chemical; CO2 foam; water spray (fog)

Unusual Fire and Explosion Hazards

None

 

 

 

Burning fluid may evolve irritating/noxious fumes. Firefighters should

Special Fire Fighting Techniques

use NIOSH/MNSA-approved self-contained breathing apparatus.

Use water to cool fire-exposed containers. Use water carefully near

 

 

 

 

 

 

exposed liquid to avoid frothing and splashing of hot liquid.

A.7

Reactivity Data

 

 

 

 

 

 

 

 

Stability

 

Stable

 

Hazardous Polymerization

Will not occur

 

Incompatible Materials

Strong oxidizers

 

Conditions to Avoid

 

Excessive heat

 

Hazardous

 

Analogous compounds evolve carbon monoxide, carbon dioxide,

 

Decomposition

 

and other unidentified fragments when burned. See A.6 - Fire and

 

Products

 

Explosion Hazards.

A.8

Health Hazard Data

 

 

 

 

 

 

 

Threshold Limit Value

 

5mg/m3 ACGIH

 

Situations to Avoid

 

Avoid breathing oil mists.

 

 

 

Ingestion

Consult physician at once. DO NOT INDUCE VOMITING. May cause

 

First Aid

 

nausea and diarrhea.

 

 

 

 

Procedures

 

Inhalation

Product is not toxic by inhalation. If oil mist is inhaled, remove to fresh

 

 

 

air and consult physician.

 

 

 

 

 

To the best of our knowledge the toxicity of this product has not been fully investigated.

 

Analogous compounds are considered to be essentially non-toxic.

A.9

Personal Protection Information

 

 

 

 

Respiratory Protection

Use in well ventilated area.

 

Ventilation

 

Local exhaust

 

Protective Gloves

 

Not required, but recommended, especially for prolonged exposure

 

Eye/Face Protection

 

Goggles

A.10 Spill or Leak Procedures

In case of spill:

Wear suitable protective equipment, especially goggles.

Stop source of spill.

Dike spill area.

Use absorbent materials to soak up fluid (e.g., sand, sawdust, commercially available materials).

Wash spill area with large amounts of water.

Properly dispose of all materials.

A.11 Waste Disposal Methods

Incinerate this product and all associated wastes in a licensed facility in accordance with federal, state, and local regulations.

33

2006SSD-75 R4 (10/10)

Image 39
Contents Copeland Scroll Compressor Module Page Table of Contents Appendix A Material Data Safety Sheet Figures Compressor Module Nomenclature Important Safety Information Safety Symbols Used in This Manual Safety Alert SymbolCompressor Module IntroductionOil coolers with fans Compressor Compressor PackageInlet gas scrubber for liquid removal Required Component-Inlet Gas Scrubber Installation GuidelinesGeneral Installation Guidelines Inlet and Discharge PressuresAmbient Temperature Range Barg SettingModule Weight Lbs. kg Compressor Module Dimensions, in. mm Installation Clearance and DimensionsCode Description Process and Instrumentation Diagrams P&IDsGeneral Considerations SwitchesSwitchStatus Electrical ControlsBrushless DC Fan Oil Cooler Fan ControlSZO44 Temperature ControlDrive Variable SpeedTypical Compressor Module power supply requirements Compressor Power data based on 480VAC Variable SpeedElectrical Requirements Control Circuit Terminations WiringOperation Pre-Startup ChecklistPost-Startup Checklist Initial Startup Compressor ModuleCheck for These Conditions Under Normal Operation Routine Maintenance MaintenanceMaintenance summary Maintenance Tools Maintenance ToolsOil Level Guidelines Maximum Speed Checking the Oil LevelOil Capacity and Type Oil Level Guidelines Minimum SpeedAdding and Removing Oil Topping Off the Oil LevelAdding Oil Draining Oil Changing the OilReplacing Oil Servicing the Scavenge Line Orifice Cleaning the Inlet ScreenChanging the Oil Filter Element Changing the Second-Stage Separator ElementMotor winding resistance Troubleshooting GuideTroubleshooting Motor Winding ResistancePlatform troubleshooting guidelines Platform Symptoms DiagnosisSpecifications Compressor Module Specifications Dual-Compressor Module Technical Support and Service Max Flow/HP as a function of discharge Configuration Suction130 140 110180 Flow rate110 120 150Components and Hazard Statement Appendix A - Material Data Safety SheetSupplier Emergency Number 989 Product Name and InformationHealth Hazard Data Spill or Leak ProceduresFire and Explosion Hazards Reactivity DataPage Page Page Page EmersonClimate.com
Related manuals
Manual 42 pages 48.05 Kb