RIDGID TS3650 manual Mounting Your Saw

Page 20

.SP6498 Belt Drive Saw 05/03 7/15/03 7:04 AM Page 20

Assembly (continued)

Mounting Your Saw

1.Place the saw upside down onto a smooth piece of cardboard or heavy paper, on the floor, so the saw is resting on the table top.

WARNING: The saw is heavy. To reduce the risk of back injury, get help to lift the saw. Hold the saw close to your body. Bend your knees so you can lift with your legs, not your back.

2.Place legs on saw so that holes in saw base and leg set line up and trim label is facing front.

3.Install screws and serrated flange hex nuts as shown.

4.Tighten all leg assembly and mounting hardware at this time.

Serrated

Flange

Hex Nut

	Leg
Screw	Base
	Base

Typical On

Each Leg

20

Image 20

Contents TS3650 Table of Contents Safety Instructions For Table Saw Safety Signal Words Before Using The SawWhen Installing Or Moving The Saw Before Each UseReduce the Risk of Dangerous Environment To reduce the risk of injury from unexpected saw movementInspect Your Blade Dress for safety Plan Ahead To Protect Your Eyes, Hands, Face and EarsPlan your work Inspect your workpieceWhenever Sawblade Is Spinning Reduce the Risk of Accidental StartingKeep Children Away Don’t Force ToolAdditional Safety Instructions For Glossary of Terms for Woodworking Dado FeatherboardFreehand GumGeneral Electrical Connections Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications Volt, 60 Hz. Tool Information Changing Motor Voltage Wire Sizes Motor Thermal Overload ProtectorUnpacking and Checking Contents List of Loose Parts Part Name Qty Operators ManualsAssembly Installing Bevel HandwheelHerc-U-Lift Caster Carton Description Qty Loose PartsInstalling Elevation Handwheel Assembling Leg StandMiter Gauge Rip Fence Storage Hook End Panel Screw Head Leg Mounting Your Saw Assembling Table Extensions Checking Table Insert To check for parallelism Minimum Clearance Rear Saw If blade is square to table Checking Blade Tilt, or Squareness of Blade to TableTo check for squareness, 90 position To check for alignment, 45 Position If blade is 45 to tableAssembling Herc-U-Lift Caster System Assembly Tips Upper AssemblyLower Assembly Center Frames Equal Distance on Each Side Tighten All Nuts Operation of Herc-U-Lift Caster System Installing Front Rip Fence Guide Bar Installing Rear Fence Guide Bar Adjusting Rip Fence Guide Bars Installing Shims Aligning Rip Fence Guide BarsInstalling Spacer Bar Rip Fence Lock Lever Adjustment Adjusting Fence Indicator Installing Blade GuardAligning Blade Guard Mounting the Motor Installing Belt Installing Belt GuardMounting Switch and End Caps 10-32Mounting Switch on Right Side Mounting Switch on Left SideSwitch Mounted on Right Side Switch Mounted on Left SideOn-Off Switch Getting to Know Your Table SawRaise blade guard. C. Loosen insert screw Switch OFF and remove plug From power source outlet before Removing or installing sawbladeTurn Switch OFF and remove Plug From Power source outletMiter gauge when not in use Storage Hooks Conveniently holds rip fenceSawdust Ejection Port Installing Zero Clearance Insert/Sawblade Remove the Existing Table InsertInstalling Zero Clearance Insert/Dado Blades Operation TipsBefore Each Use Safety Instructions for Basic Saw OperationsInspect your saw Inspect your work area Plan your workInspect your workpiece Plan your cutReduce the Risk of Accidental Starting Work Feed Devices Attaching Wood Face Board Push Block Making the baseAuxiliary Fence Making the handlePutting it Together Making the sideInstall extension Work Support for Material over WideAdditional Safety Instructions for Crosscutting Using the Miter GaugeBasic Saw Operations CrosscuttingRepetitive Crosscutting Compound Crosscutting Miter CrosscuttingBevel Crosscutting Using the Rip Fence Additional Safety Instructions for Rip CutsRipping Once the trailing end is on the tableBevel Ripping Narrow Work Using Featherboards for Thru- Sawing Using Featherboards for Non Thru-SawingResawing Using Carbide Tipped Blades DadoingRabbeting Ploughing and MoldingMolding Adjustments Miter Gauge Adjusting Stop ScrewsHerc-U-Lift Caster System MaintenanceMaintaining Your Table Saw Ridgid Recommends the Following Accessories LubricationSKU No Miter Gauge Hold Down AC1022240V 240V Wiring Diagrams120V Troubleshooting Troubleshooting Troubleshooting SP6498 Belt Drive Saw 05/03 7/15/03 705 AM Catalog No. TS3650 Model No TS36500 Serial No RIDGID, INC