RIDGID TS3650 manual Work Support for Material over Wide, Install extension

Page 56

.SP6498 Belt Drive Saw 05/03 7/15/03 7:05 AM Page 56

Work Feed Devices (continued)

Work Support for Material over 26"

Wide

When ripping material in excess of 26" wide, install this fence extension to support the edge of the work and prevent material from sliding under rip fence.

Making the base:

•Start with a piece of 3/4" plywood at least 4" wide and at least 25" long.

•Cut the base to size as shown.

Making the side:

•Start with a piece of 1/2" plywood at least 3-1/2" wide and 25" long.

•Cut the side to size as shown.

•Putting it together:

•Drill holes in side as shown.

•Put the pieces together as shown.

•Install four wood screws at least #8

x1-1/4" long in lower holes.

Install extension:

• Slide three 1/4-20 x 1" long square or hex head bolts into T-slot away from blade.

	• Align bolts with 3/8" holes. Place
	the side against the fence with the
	base extending under the fence as	Support
	shown.	Support
	shown.	Workpiece
	• Install a flat washer and 1/4-20 nut	Workpiece
	• Install a flat washer and 1/4-20 nut
	on each bolt. Hold device tight
	against side and bottom of fence
	and tighten nuts.

56

Image 56

Contents TS3650 Table of Contents Safety Instructions For Table Saw Safety Signal Words Before Using The SawWhen Installing Or Moving The Saw Before Each UseReduce the Risk of Dangerous Environment To reduce the risk of injury from unexpected saw movementInspect Your Blade Dress for safety Plan Ahead To Protect Your Eyes, Hands, Face and EarsPlan your work Inspect your workpieceWhenever Sawblade Is Spinning Reduce the Risk of Accidental StartingKeep Children Away Don’t Force ToolAdditional Safety Instructions For Glossary of Terms for Woodworking Dado FeatherboardFreehand GumGeneral Electrical Connections Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications Volt, 60 Hz. Tool Information Changing Motor Voltage Wire Sizes Motor Thermal Overload ProtectorUnpacking and Checking Contents List of Loose Parts Part Name Qty Operators ManualsAssembly Installing Bevel HandwheelHerc-U-Lift Caster Carton Description Qty Loose PartsInstalling Elevation Handwheel Assembling Leg StandMiter Gauge Rip Fence Storage Hook End Panel Screw Head Leg Mounting Your Saw Assembling Table Extensions Checking Table Insert To check for parallelism Minimum Clearance Rear Saw If blade is square to table Checking Blade Tilt, or Squareness of Blade to TableTo check for squareness, 90 position To check for alignment, 45 Position If blade is 45 to tableAssembling Herc-U-Lift Caster System Assembly Tips Upper AssemblyLower Assembly Center Frames Equal Distance on Each Side Tighten All Nuts Operation of Herc-U-Lift Caster System Installing Front Rip Fence Guide Bar Installing Rear Fence Guide Bar Adjusting Rip Fence Guide Bars Installing Shims Aligning Rip Fence Guide BarsInstalling Spacer Bar Rip Fence Lock Lever Adjustment Adjusting Fence Indicator Installing Blade GuardAligning Blade Guard Mounting the Motor Installing Belt Installing Belt GuardMounting Switch and End Caps 10-32Mounting Switch on Right Side Mounting Switch on Left SideSwitch Mounted on Right Side Switch Mounted on Left SideOn-Off Switch Getting to Know Your Table SawRaise blade guard. C. Loosen insert screw Switch OFF and remove plug From power source outlet before Removing or installing sawbladeTurn Switch OFF and remove Plug From Power source outletMiter gauge when not in use Storage Hooks Conveniently holds rip fenceSawdust Ejection Port Installing Zero Clearance Insert/Sawblade Remove the Existing Table InsertInstalling Zero Clearance Insert/Dado Blades Operation TipsBefore Each Use Safety Instructions for Basic Saw OperationsInspect your saw Inspect your work area Plan your workInspect your workpiece Plan your cutReduce the Risk of Accidental Starting Work Feed Devices Attaching Wood Face Board Push Block Making the baseAuxiliary Fence Making the handlePutting it Together Making the sideInstall extension Work Support for Material over WideAdditional Safety Instructions for Crosscutting Using the Miter GaugeBasic Saw Operations CrosscuttingRepetitive Crosscutting Compound Crosscutting Miter CrosscuttingBevel Crosscutting Using the Rip Fence Additional Safety Instructions for Rip CutsRipping Once the trailing end is on the tableBevel Ripping Narrow Work Using Featherboards for Thru- Sawing Using Featherboards for Non Thru-SawingResawing Using Carbide Tipped Blades DadoingRabbeting Ploughing and MoldingMolding Adjustments Miter Gauge Adjusting Stop ScrewsHerc-U-Lift Caster System MaintenanceMaintaining Your Table Saw Ridgid Recommends the Following Accessories LubricationSKU No Miter Gauge Hold Down AC1022240V 240V Wiring Diagrams120V Troubleshooting Troubleshooting Troubleshooting SP6498 Belt Drive Saw 05/03 7/15/03 705 AM Catalog No. TS3650 Model No TS36500 Serial No RIDGID, INC