RIDGID TS3650 manual Attaching Wood Face Board

Page 53

.SP6498 Belt Drive Saw 05/03 7/15/03 7:05 AM Page 53

Attaching Wood Face Board

1.A T-slot is provided in the rip fence for attaching a wood facing when using the dado head, or molding head, featherboards or other jigs and fixtures.

2.Select a piece of smooth straight wood approximately 3/4 inch thick, and the same length as the rip fence.

3.To fasten wood face to the fence use the three 1/4"20 x 3/4" square head bolts, lock-washers, flat washers and nuts supplied. Counterbore three 3/4" dia. holes 3/8" deep into the 3/4" board at the dimen-sion shown. Avoid placing screws directly over blade.

4.Drill a 9/32" clearance hole through the board at each counterbore location.

53

Image 53

Contents TS3650 Table of Contents Safety Signal Words Before Using The Saw Safety Instructions For Table SawBefore Each Use When Installing Or Moving The SawReduce the Risk of Dangerous Environment To reduce the risk of injury from unexpected saw movementInspect Your Blade Plan Ahead To Protect Your Eyes, Hands, Face and Ears Dress for safetyPlan your work Inspect your workpieceReduce the Risk of Accidental Starting Whenever Sawblade Is SpinningKeep Children Away Don’t Force ToolAdditional Safety Instructions For Glossary of Terms for Woodworking Featherboard DadoFreehand GumGeneral Electrical Connections Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications Volt, 60 Hz. Tool Information Changing Motor Voltage Motor Thermal Overload Protector Wire SizesUnpacking and Checking Contents Operators Manuals List of Loose Parts Part Name QtyInstalling Bevel Handwheel AssemblyHerc-U-Lift Caster Carton Description Qty Loose PartsAssembling Leg Stand Installing Elevation HandwheelMiter Gauge Rip Fence Storage Hook End Panel Screw Head Leg Mounting Your Saw Assembling Table Extensions Checking Table Insert To check for parallelism Minimum Clearance Rear Saw If blade is square to table Checking Blade Tilt, or Squareness of Blade to TableTo check for squareness, 90 position If blade is 45 to table To check for alignment, 45 PositionUpper Assembly Assembling Herc-U-Lift Caster System Assembly TipsLower Assembly Center Frames Equal Distance on Each Side Tighten All Nuts Operation of Herc-U-Lift Caster System Installing Front Rip Fence Guide Bar Installing Rear Fence Guide Bar Aligning Rip Fence Guide Bars Adjusting Rip Fence Guide Bars Installing ShimsInstalling Spacer Bar Rip Fence Lock Lever Adjustment Installing Blade Guard Adjusting Fence IndicatorAligning Blade Guard Mounting the Motor Installing Belt Guard Installing Belt10-32 Mounting Switch and End CapsMounting Switch on Left Side Mounting Switch on Right SideSwitch Mounted on Right Side Switch Mounted on Left SideGetting to Know Your Table Saw On-Off SwitchRaise blade guard. C. Loosen insert screw Removing or installing sawblade Switch OFF and remove plug From power source outlet beforeTurn Switch OFF and remove Plug From Power source outletStorage Hooks Conveniently holds rip fence Miter gauge when not in useSawdust Ejection Port Remove the Existing Table Insert Installing Zero Clearance Insert/SawbladeOperation Tips Installing Zero Clearance Insert/Dado BladesBefore Each Use Safety Instructions for Basic Saw OperationsInspect your saw Plan your work Inspect your work areaInspect your workpiece Plan your cutReduce the Risk of Accidental Starting Work Feed Devices Attaching Wood Face Board Making the base Push BlockMaking the handle Auxiliary FencePutting it Together Making the sideWork Support for Material over Wide Install extensionUsing the Miter Gauge Additional Safety Instructions for CrosscuttingBasic Saw Operations CrosscuttingRepetitive Crosscutting Compound Crosscutting Miter CrosscuttingBevel Crosscutting Additional Safety Instructions for Rip Cuts Using the Rip FenceOnce the trailing end is on the table RippingBevel Ripping Narrow Work Using Featherboards for Non Thru-Sawing Using Featherboards for Thru- SawingResawing Dadoing Using Carbide Tipped BladesPloughing and Molding RabbetingMolding Miter Gauge Adjusting Stop Screws AdjustmentsHerc-U-Lift Caster System MaintenanceMaintaining Your Table Saw Lubrication Ridgid Recommends the Following AccessoriesSKU No Miter Gauge Hold Down AC1022240V 240V Wiring Diagrams120V Troubleshooting Troubleshooting Troubleshooting SP6498 Belt Drive Saw 05/03 7/15/03 705 AM Catalog No. TS3650 Model No TS36500 Serial No RIDGID, INC