RIDGID TS3650 manual Lower Assembly

Page 28

.SP6498 Belt Drive Saw 05/03 7/15/03 7:04 AM Page 28

Assembly (continued)

Lower Assembly

1. Locate the following hardware.

4Hex Head Screw w/Washer 1/4-20 x 2

4 Lock Nut 1/4-20

4Hex Nut w/Serrated Flange 5/16-18

2Hex Nut w/Serrated Flange 7/16

1U-Bolt

2.From the loose parts find the following:

2Caster

2Tube Front (13-7/8" Long)

1Tube Support (17-1/4" Long)

1Tube U-Bolt (19-5/8" Long)

3.Assemble support tube (17-3/4 inch length) to both front tubes (13-7/8 inch length) using two each 1/4-20 x 2 hex head screw, and lock nut as shown. Loosely assemble at this time.

NOTE: The larger hole at the end of the front tube must face down as shown.

4.Align and assemble U-bolt tube (19-5/8 inch length) with holes in the front tube using two each 1/4-20 x 2 hex head screw, and lock nut as shown. Loosely assemble at this time.

5.Assemble 5/16 nut on each side of U-bolt as shown with serration facing tubing.

6.Place U-bolt through holes in U-bolt tube. Assemble 5/16 nuts on each side of U-bolt as shown with serration facing tube.

7.Adjust U-bolt about two inches from tube.

8.Assemble caster through tube. Fasten with 7/16 nut as shown. Tighten nuts securely. Use adjustable wrench on caster stem hex to keep stem from turning while tightening nut.

Assemble each tube exactly as shown. Note both front tubes are placed on top of the tube U-bolt and tube support as shown.

28

Image 28
Contents TS3650 Table of Contents Safety Instructions For Table Saw Safety Signal Words Before Using The SawWhen Installing Or Moving The Saw Before Each UseReduce the Risk of Dangerous Environment To reduce the risk of injury from unexpected saw movementInspect Your Blade Dress for safety Plan Ahead To Protect Your Eyes, Hands, Face and EarsPlan your work Inspect your workpieceWhenever Sawblade Is Spinning Reduce the Risk of Accidental StartingKeep Children Away Don’t Force ToolAdditional Safety Instructions For Glossary of Terms for Woodworking Dado FeatherboardFreehand GumPower Supply and Motor Specifications Motor Specifications and Electrical RequirementsGeneral Electrical Connections Volt, 60 Hz. Tool Information Changing Motor Voltage Wire Sizes Motor Thermal Overload ProtectorUnpacking and Checking Contents List of Loose Parts Part Name Qty Operators ManualsAssembly Installing Bevel HandwheelHerc-U-Lift Caster Carton Description Qty Loose PartsInstalling Elevation Handwheel Assembling Leg StandMiter Gauge Rip Fence Storage Hook End Panel Screw Head Leg Mounting Your Saw Assembling Table Extensions Checking Table Insert To check for parallelism Minimum Clearance Rear Saw To check for squareness, 90 position Checking Blade Tilt, or Squareness of Blade to TableIf blade is square to table To check for alignment, 45 Position If blade is 45 to tableAssembling Herc-U-Lift Caster System Assembly Tips Upper AssemblyLower Assembly Center Frames Equal Distance on Each Side Tighten All Nuts Operation of Herc-U-Lift Caster System Installing Front Rip Fence Guide Bar Installing Rear Fence Guide Bar Adjusting Rip Fence Guide Bars Installing Shims Aligning Rip Fence Guide BarsInstalling Spacer Bar Rip Fence Lock Lever Adjustment Adjusting Fence Indicator Installing Blade GuardAligning Blade Guard Mounting the Motor Installing Belt Installing Belt GuardMounting Switch and End Caps 10-32Mounting Switch on Right Side Mounting Switch on Left SideSwitch Mounted on Right Side Switch Mounted on Left SideOn-Off Switch Getting to Know Your Table SawRaise blade guard. C. Loosen insert screw Switch OFF and remove plug From power source outlet before Removing or installing sawbladeTurn Switch OFF and remove Plug From Power source outletMiter gauge when not in use Storage Hooks Conveniently holds rip fenceSawdust Ejection Port Installing Zero Clearance Insert/Sawblade Remove the Existing Table InsertInstalling Zero Clearance Insert/Dado Blades Operation TipsInspect your saw Safety Instructions for Basic Saw OperationsBefore Each Use Inspect your work area Plan your workInspect your workpiece Plan your cutReduce the Risk of Accidental Starting Work Feed Devices Attaching Wood Face Board Push Block Making the baseAuxiliary Fence Making the handlePutting it Together Making the sideInstall extension Work Support for Material over WideAdditional Safety Instructions for Crosscutting Using the Miter GaugeBasic Saw Operations CrosscuttingRepetitive Crosscutting Bevel Crosscutting Miter CrosscuttingCompound Crosscutting Using the Rip Fence Additional Safety Instructions for Rip CutsRipping Once the trailing end is on the tableBevel Ripping Narrow Work Using Featherboards for Thru- Sawing Using Featherboards for Non Thru-SawingResawing Using Carbide Tipped Blades DadoingRabbeting Ploughing and MoldingMolding Adjustments Miter Gauge Adjusting Stop ScrewsMaintaining Your Table Saw MaintenanceHerc-U-Lift Caster System Ridgid Recommends the Following Accessories LubricationSKU No Miter Gauge Hold Down AC1022120V 240V Wiring Diagrams240V Troubleshooting Troubleshooting Troubleshooting SP6498 Belt Drive Saw 05/03 7/15/03 705 AM Catalog No. TS3650 Model No TS36500 Serial No RIDGID, INC