RIDGID TS3650 manual Adjustments, Miter Gauge Adjusting Stop Screws

Page 68

.SP6498 Belt Drive Saw 05/03 7/15/03 7:05 AM Page 68

Adjustments

WARNING: For your own safety, turn switch “OFF” and remove plug from power source outlet before making any adjustments.

Miter Gauge

NOTE: The graduations are manufac-tured to very close tolerances which pro-vide ample accuracy for fine woodworking. In some cases where extreme accuracy is required, when making angle cuts, for example, make a trial cut and then recheck it. There are adjustable screw stops for the stop pin at 0° and 45° right and left positions for conveniently setting the miter gauge to cut miters at these standard angles.

Adjusting Stop Screws

A.Loosen lock nut of screw for 0° stop.

B.Place 90° square against the miter gauge bar and the face of the miter gauge head.

C.If adjustment is needed loosen handle of miter gauge. Adjust miter gauge head flush to square. Tighten lock knob.

D.Adjust stop screw until it rests against the stop pin and tighten lock nut.

E.Adjust 45°, left and right using a 45° triangle or a protractor of a square using the above procedure.

The miter gauge head should swivel smoothly on the bar after the knob is loosened. To adjust this swivel movement:

A.Loosen the knob.

B.Loosen set screw with a 2.5mm hex wrench.

C.If the head is too loose turn the flat-head screw in a clockwise direction.

If the head is too tight and will not swivel smoothly turn the flathead screw counterclockwise.

D.Tighten set screw.

Flat Head Screw

Set Screw

68

Image 68
Contents TS3650 Table of Contents Safety Instructions For Table Saw Safety Signal Words Before Using The SawWhen Installing Or Moving The Saw Before Each UseReduce the Risk of Dangerous Environment To reduce the risk of injury from unexpected saw movementInspect Your Blade Dress for safety Plan Ahead To Protect Your Eyes, Hands, Face and EarsPlan your work Inspect your workpieceWhenever Sawblade Is Spinning Reduce the Risk of Accidental StartingKeep Children Away Don’t Force ToolAdditional Safety Instructions For Glossary of Terms for Woodworking Dado FeatherboardFreehand GumGeneral Electrical Connections Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications Volt, 60 Hz. Tool Information Changing Motor Voltage Wire Sizes Motor Thermal Overload ProtectorUnpacking and Checking Contents List of Loose Parts Part Name Qty Operators ManualsAssembly Installing Bevel HandwheelHerc-U-Lift Caster Carton Description Qty Loose PartsInstalling Elevation Handwheel Assembling Leg StandMiter Gauge Rip Fence Storage Hook End Panel Screw Head Leg Mounting Your Saw Assembling Table Extensions Checking Table Insert To check for parallelism Minimum Clearance Rear Saw If blade is square to table Checking Blade Tilt, or Squareness of Blade to TableTo check for squareness, 90 position To check for alignment, 45 Position If blade is 45 to tableAssembling Herc-U-Lift Caster System Assembly Tips Upper AssemblyLower Assembly Center Frames Equal Distance on Each Side Tighten All Nuts Operation of Herc-U-Lift Caster System Installing Front Rip Fence Guide Bar Installing Rear Fence Guide Bar Adjusting Rip Fence Guide Bars Installing Shims Aligning Rip Fence Guide BarsInstalling Spacer Bar Rip Fence Lock Lever Adjustment Adjusting Fence Indicator Installing Blade GuardAligning Blade Guard Mounting the Motor Installing Belt Installing Belt GuardMounting Switch and End Caps 10-32Mounting Switch on Right Side Mounting Switch on Left SideSwitch Mounted on Right Side Switch Mounted on Left SideOn-Off Switch Getting to Know Your Table SawRaise blade guard. C. Loosen insert screw Switch OFF and remove plug From power source outlet before Removing or installing sawbladeTurn Switch OFF and remove Plug From Power source outletMiter gauge when not in use Storage Hooks Conveniently holds rip fenceSawdust Ejection Port Installing Zero Clearance Insert/Sawblade Remove the Existing Table InsertInstalling Zero Clearance Insert/Dado Blades Operation TipsBefore Each Use Safety Instructions for Basic Saw OperationsInspect your saw Inspect your work area Plan your workInspect your workpiece Plan your cutReduce the Risk of Accidental Starting Work Feed Devices Attaching Wood Face Board Push Block Making the baseAuxiliary Fence Making the handlePutting it Together Making the sideInstall extension Work Support for Material over WideAdditional Safety Instructions for Crosscutting Using the Miter GaugeBasic Saw Operations CrosscuttingRepetitive Crosscutting Compound Crosscutting Miter CrosscuttingBevel Crosscutting Using the Rip Fence Additional Safety Instructions for Rip CutsRipping Once the trailing end is on the tableBevel Ripping Narrow Work Using Featherboards for Thru- Sawing Using Featherboards for Non Thru-SawingResawing Using Carbide Tipped Blades DadoingRabbeting Ploughing and MoldingMolding Adjustments Miter Gauge Adjusting Stop ScrewsHerc-U-Lift Caster System MaintenanceMaintaining Your Table Saw Ridgid Recommends the Following Accessories LubricationSKU No Miter Gauge Hold Down AC1022240V 240V Wiring Diagrams120V Troubleshooting Troubleshooting Troubleshooting SP6498 Belt Drive Saw 05/03 7/15/03 705 AM Catalog No. TS3650 Model No TS36500 Serial No RIDGID, INC