Husqvarna 966648206 manuel dutilisation Fuel Handling

Page 19

FUEL HANDLING

Fuel

Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

!

WARNING! Always ensure there is

adequate ventilation when handling fuel.

 

Gasoline

Use good quality unleaded gasoline.

CAUTION! Engines equipped with catalytic converters must be run on unleaded fuel mixtures. Leaded gasoline will destroy the catalytic converter and it will no longer serve its purpose. The green fuel cap on saws fitted with catalytic converters means that only unleaded gasoline can be used.

The lowest recommended octane grade is 87 ((RON+MON)/2). If you run the engine on a lower octane grade than 87 so-called knocking can occur. This gives rise to a high engine temperature and increased bearing load, which can result in serious engine damage.

When working with continuous high revs (e.g. limbing) a higher octane is recommended.

Environment fuel

HUSQVARNA recommends the use of alkylate fuel or environmental fuel for four-stroke engines blended with two-stroke oil as set out below. Note that carburetor adjustment may be necessary when changing the type of fuel (see instructions under the heading Carburetor).

Running-in

Avoid running at a too high speed for extended periods during the first 10 hours.

Two-stroke oil

For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines.

Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

Never use oil intended for four-stroke engines.

Mixing ratio

1:50 (2%) for all engines.

Gasoline, litre

Two-stroke oil, litre

 

 

 

2% (1:50)

 

 

5

0,10

 

 

10

0,20

 

 

15

0,30

 

 

20

0,40

 

 

US gallon

US fl. oz.

 

 

1

2 1/2

 

 

2 1/2

6 1/2

 

 

5

12 7/8

 

 

Mixing

Always mix the gasoline and oil in a clean container intended for fuel.

Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline.

Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank.

Do not mix more than one month’s supply of fuel at a time.

If the machine is not used for some time the fuel tank should be emptied and cleaned.

Chain oil

We recommend the use of special oil (chain oil) with good adhesion characteristics.

Never use waste oil. This results in damage to the oil pump, the bar and the chain.

It is important to use oil of the right grade (suitable viscosity range) to suit the air temperature.

In temperatures below 0°C (32°F) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components.

Contact your service agent when choosing chain oil.

English 19

Image 19
Contents Operator′s manual Manuel d’utilisation Symbols on the machine KEY to SymbolsDecompression valve Press EPA Symbols in the operator’s manualContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsPersonal protective equipment Always use common senseCarbon monoxide poisoning Chain brake and front hand guard Machine′s safety equipmentThrottle lockout Vibration damping system Stop switchChain catcher Right hand guardGuide bar Cutting equipmentGeneral rules Cutting equipment designed to reduce kickbackGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth General advice on adjusting depth gauge settingIncreased if the depth gauge setting is Adjustment of depth gauge settingChecking chain lubrication Tensioning the chainLubricating cutting equipment Filling with chain oilNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment General Safety Precautions Fitting the bar and chain AssemblyWorking with the chain Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageCold engine Starting and StoppingStarting and stopping StartingStopping General working instructions Basic safety rulesWorking Techniques Before useWorking Techniques Basic cutting technique Safe distance Tree felling techniqueFelling direction Your saw Clearing the trunk and preparing your retreatFelling cut Felling Training we advise you not to fell treesCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeWhat is kickback? How to avoid kickbackCarburetor adjustment MaintenanceGeneral Checking the brake trigger Checking the inertia brake releaseMuffler Changing a broken or worn starter cord StarterTensioning the recoil spring Fitting the starter Air filterSpark plug Changing a broken recoil springNeedle bearing lubrication Adjustment of the oil pumpRunning when making adjustments Lubricating the bar tip sprocketHeated handles Air Injection centrifugal cleaningTemperature 0C 32F or colder Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data058/1,5 mm Saw chain filing and file gaugesRecommended cutting equipment for Canada 050/1,3 mmYour Warranty Rights and Obligations Federal Emission Control Warranty StatementEmission Control Warranty Parts List Other safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsSymboles sur la machine Explication DES SymbolesDécompresseur Le Symboles dans le manuel Sommaire SommaireConsignes de sécurité pour les utilisateurs de Cher client Quels sont les composants de la tronçonneuse? Quels Sont LES COMPOSANTS?AVERTISSEMENT! Ne jamais modifier Instructions Générales DE SécuritéÉquipement de protection personnelle Utilisez toujours votre bon sensFrein de chaîne avec arceau protecteur Équipement de sécurité de la machineInstructions Générales DE Sécurité Système anti-vibrations Blocage de l’accélérationCapteur de chaîne Protection de la main droiteÉquipement de coupe anti-rebond Équipement de coupeSilencieux Règles élémentairesChaîne Affûtage et réglage de l’épaisseur du copeau de la chaîneGénéralités concernant l’affûtage des dents Généralités sur le réglage de l’épaisseur du copeau AVERTISSEMENT! La tendance auRespectées Affûtage de la dentLubrification de l’équipement de coupe Tension de la chaîneRéglage de l’épaisseur du copeau Graissage du roulement à aiguilles Remplissage d’huile de chaîneContrôle de la lubrification de la chaîne Pignon d’entraînementContrôle de l’usure de l’équipement de coupe Montage du guide-chaîne et de la chaîne MontageAVERTISSEMENT! Utiliser des gants Carburant Manipulation DU CarburantRemisage prolongé Remplissage de carburantSécurité carburant Transport et rangementAVERTISSEMENT! Contrôler les points Démarrage ET ArrêtDémarrage et arrêt DémarrageDe la poussière de copeaux peut Prolongée des gaz d’échappement duConstituer un danger pour la santé Règles élémentaires de sécurité Techniques DE TravailAvant chaque utilisation Méthodes de travailRègles élémentaires Terminologie Technique de base pour la coupeAVERTISSEMENT! N’utilisez jamais une GénéralitésTechniques d’abattage Encoche Sens d’abattageÉmondage des branches basses et voie de retraite Abattage AVERTISSEMENT! Il est déconseillé auxTrait de chute Solution à un abattage ratéRécupération d’un arbre accroché Règles générales Mesures anti-rebondQu’est-ce qu’un rebond? Sciage d’un arbre ou d’une branche pliésTronçonnage en rondins Fonctionnement EntretienGénéralités Réglage du carburateurContrôle de l’effet de freinage Contrôle de la fonction d’inertieSilencieux Lanceur Remplacement d’une corde de lanceur rompue ou uséeMontage du lanceur Remplacement d’un ressort de rappel rompuFiltre à air Mise sous tension du ressortRéglage de la pompe à huile BougieGraissage du pignon d’entraînement du guide Graissage du roulement à aiguillesTempérature inférieure ou égale à 0C Système de refroidissementÉpuration centrifuge Air Injection Utilisation hivernaleChauffage électrique du carburateur Poignées chauffantesEntretien quotidien Entretien hebdomadaire Entretien mensuel Schéma d’entretienCaractéristiques techniques Caractéristiques TechniquesAffûtage de la chaîne et gabarits d’affûtage Équipement de coupe recommandé pour CanadaVOS Droits ET Obligations EN Garantie Déclaration DE Garantie Pour LA Lutte Contre LESService APRÈS-VENTE Précautions à prendre pour se protéger des rebonds Précautions Sécuritaires Conformant AUX NormesAutres consignes de sécurité Précautions Sécuritaires Conformant AUX Normes Page Page Page Page Page Original instructions Instructions d’origine 1154131-32

966648206 specifications

The Husqvarna 966648206 is a reliable and innovative garden tractor designed for homeowners who seek efficiency and convenience for their lawn care needs. This model stands out due to its powerful performance, user-friendly features, and advanced technology, making it an excellent choice for those looking to maintain their lawns effortlessly.

At the heart of the Husqvarna 966648206 is a robust engine that delivers exceptional power and torque. This ensures that the tractor can tackle a variety of tasks, from mowing to transporting materials, with ease. The engine is designed for fuel efficiency, allowing users to spend more time working and less time refueling, which is a significant plus for those managing larger properties.

The design of the Husqvarna 966648206 is user-oriented, featuring an ergonomic seat and an adjustable steering wheel to enhance comfort during extended use. The intuitive dashboard provides easy access to controls, allowing the user to adjust settings quickly while keeping their focus on the task at hand. This tractor's hydrostatic transmission lends itself to smooth and seamless operation, enabling seamless speed adjustments without the need for complex gear shifting.

One of the notable features of the Husqvarna 966648206 is its cutting deck, which is engineered for optimal grass cutting performance. The durable deck construction ensures longevity, while its design allows for superior airflow and cut quality, ensuring a clean and even cut every time. The cutting height is easily adjustable, accommodating different grass lengths and preferences.

In terms of technology, the Husqvarna 966648206 is equipped with features like a smart and efficient mower energy management system that optimizes the cutting process for performance and battery longevity. Additionally, the tractor's compatibility with various accessories, such as mulchers and baggers, adds to its versatility, allowing homeowners to customize their lawn care experience.

Safety is also a priority in the design of the Husqvarna 966648206. With features such as an automatic blade brake system and a reliable parking brake, users can rest assured that they are using a machine designed with their safety in mind.

Overall, the Husqvarna 966648206 is a feature-rich garden tractor that combines power, comfort, and advanced technology to meet the needs of any homeowner. Its thoughtful design and reliable performance make lawn maintenance a more enjoyable and efficient experience. Whether tackling a small garden or a larger lawn, this tractor is up to the task, providing excellent value and results for every gardening enthusiast.