Hobart Welding Products OM-240 438E manual Generator Power Guidelines, Selecting Equipment

Page 48

SECTION 12 − GENERATOR POWER GUIDELINES

.The views in this section are intended to be representative of all engine-driven welding generators. Your unit may differ from those shown.

12-1. Selecting Equipment

1

2

3

OR

1Generator Power Receptacles − Neutral Bonded To Frame

23-Prong Plug From Case Grounded Equipment

32-Prong Plug From Double Insulated Equipment

.Be sure equipment has double

insulated symbol and/or word- ing on it.

! Do not use 2-prong plug un- less equipment is double in- sulated.

gen_pwr 2010−04 − ST-800 577

12-2. Grounding Generator To Truck Or Trailer Frame

1 2

GND/PE

3

!Always ground generator frame to vehicle frame to pre- vent electric shock and static electricity hazards.

!Also see AWS Safety & Health Fact Sheet No. 29, Grounding of Portable And Vehicle Mounted Welding Generators.

1Equipment Grounding Terminal (On Front Panel)

2Grounding Cable (Not Supplied)

3Metal Vehicle Frame

Connect cable from equipment ground terminal to metal vehicle frame. Use #8 AWG or larger insu- lated copper wire.

.Electrically bond generator

frame to vehicle frame by met- al-to-metal contact.

! Bed liners, shipping skids, and some running gear insu- late the welding generator from the vehicle frame. Al- ways connect a ground wire from the generator equip- ment grounding terminal to bare metal on the vehicle frame as shown.

! If unit does not have GFCI re- ceptacles, use GFCI-pro- tected extension cord.

800 652-D

OM-240 438 Page 44

Image 48

Contents OM-240 438E ProcessesDescription From Hobart to You Protect Your InvestmentTable of Contents 10-1 Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can burnFumes and Gases can be hazardous Buildup of GAS can injure or killARC Rays can burn eyes and skin Welding can cause fire or explosionEngine Hazards Hydraulic Hazards Compressed Air HazardsHydraulic Equipment can injure or kill Hydraulic Fluid can injure or killCompressed AIR can injure or kill Fire or Explosion hazardOverheating can damage motors Falling Equipment can injureCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Implanted Medical Devices Signification des symboles − Consignes DE Sécurité − Lire Avant UtilisationUN Choc Électrique peut tuer Indique des instructions spécifiquesLES Pièces Chaudes peuvent provoquer des brûlures LES Fumées ET LES GAZ peu- vent être dangereuxLE Soudage peut provoquer un incendie ou une explosion LE Bruit peut affecter l’ouïe’EXPLOSION DE LA Batterie peut provoquer des blessures Les Pièces Mobiles peuvent causer des blessuresLES Étincelles À L’ÉCHAPPEMENT peuvent provoquer un incendie LA Chaleur DU Moteur peut pro- voquer un incendieLire LES Instructions Risque D’INCENDIE OU LA Chute DE L’ÉQUIPEMENT peut provoquer des blessuresLE Surchauffement peut endommager le moteur électrique LES Étincelles Projetées peuvent provoquer des blessuresProposition californienne 65 Avertissements UNE Remorque QUI Bascule peut provoquer des blessuresLE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécurité Informations relatives aux CEMEn ce qui concerne les implants médicaux − Specifications Symbol DefinitionsWeld, Power, and Engine Specifications − DefinitionsDimensions, Weights, And Operating Angles Weight 562 lb 254 kgDimensions For Units With Optional Running Gear DimensionsDuty Cycle Duty CycleFor CC/AC Mode For CC/DC ModeVolt-Ampere Curves Generator Power Curve Fuel Consumption− Installation Installing Welding GeneratorSerial Number And Rating Label Location Movement Location / Airflow ClearanceGrounding Generator To Truck Or Trailer Frame GND/PEEngine Prestart Checks OilInstalling Exhaust Pipe Connecting Or Replacing the BatteryConnect negative − battery cable last + −Connecting To Weld Output Terminals Stop engine Failure to properly connectTools Needed 3/4 Selecting Weld Cable Sizes 150 ft 200 ft 250 ft350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m 100 150 200 250Start Your Professional Welding Career Now Engine Control Switch − Operating the Welding GeneratorFront Panel Controls Fine ControlCold Weather Engine Operation InfrequentlyLoaded Frequently LoadedTypical Stick Welding Connections And Control Settings Stop engineElectrode − Operating Auxiliary Equipment Standard ReceptaclesGfci Receptacle Option At least once a month, run engine atSimultaneous Weld And Power Wiring Optional 240 Volt PlugCurrent Available in Amperes 240 Receptacle− Maintenance Maintenance LabelRoutine Maintenance 100200 500Servicing Air Cleaner Changing Engine Oil, Oil Filter, and Fuel Filter Stop engine and let coolClose valve and valve cap Before Adding Oil Running engineAdjusting Engine Speed Idle Speed AdjustmentWeld/Power Speed Adjustment Turn idle speed screw for fine ad- justmentsStop engine. Disconnect negative − battery cable Overload ProtectionServicing Optional Spark Arrestor Fuse F1 See Section− Troubleshooting Welding TroubleshootingGenerator Power Troubleshooting Trouble RemedyEngine Troubleshooting Check receptacle wiring and connectionsErs SR2 and SR3 Check fuel level− Parts List Control switch S2, and throttle solenoid TS1Recommended Spare Parts Recommended Spare Parts− Electrical Diagrams Circuit Diagram For Welding Generator240 424-B − Generator Power Guidelines Selecting EquipmentGrounding When Supplying Building Systems How Much Power Does Equipment Require?Use ground device as stated Electrical codesApproximate Power Requirements For Industrial Motors Approximate Power Requirements For Farm/Home EquipmentIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running WattsApproximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running WattsPower Required To Start Motor How Much Power Can Generator Supply?Single-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 / Volts = Starting AmperageTypical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible Stick Welding Procedure − Stick Welding Smaw GuidelinesWeld current starts when Electrode touches workElectrode and Amperage Selection Chart Striking an ArcScratch Technique Tapping TechniquePoor Weld Bead Characteristics Good Weld Bead CharacteristicsPositioning Electrode Holder End View Of Work Angle Side View Of Electrode Angle 10-30Conditions That Affect Weld Bead Shape Electrode Movement During WeldingElectrode Angle NormalGroove Butt Joints Lap JointTee Joint Or LessTroubleshooting Weld TestPossible Causes Corrective Actions Weld beadLack of Penetration Good Penetration Good Penetration Excessive PenetrationMetal remains DirectionSOCKET/WRENCH Selection Table Standard Metric Service SupportAssistance Contact your Distributor for Hobart Welding Products