Power Tool Safety Rules, Work Area | Bosch Power Tools CS10 specification

BM 1619X00886 3-05 3/20/05 9:27 PM Page 2

	Power Tool Safety Rules
	Read and understand all instructions. Failure to follow all instructions listed
! WARNING
	below, may result in electric shock, fire and/or serious personal injury.

	SAVE THESE INSTRUCTIONS

Work Area

Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

Keep by-standers, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

Electrical Safety

Double Insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double Insulation eliminates the need for the three wire grounded power cord and grounded power supply system. Before plugging in the tool, be certain the outlet voltage supplied is within the voltage marked on the nameplate. Do not use “AC only” rated tools with a DC power supply.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. If operating the power tool in damp locations is unavoidable, a Ground Fault Circuit Interrupter must be used to supply the power to your tool. Electrician’s rubber gloves and footwear will further enhance your personal safety.

Don't expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged

cords immediately. Damaged cords increase the risk of electric shock.

When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W." These cords are rated for outdoor use and reduce the risk of electric shock. Refer to “Recommended sizes of Extension Cords” in the Accessory section of this manual.

Personal Safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.

Keep handles dry, clean and free from oil and grease.

Avoid accidental starting. Be sure switch is “OFF” before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch “ON” invites accidents.

Remove adjusting keys or wrenches before turning the tool “ON”. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

Tool Use and Care

Use clamps or other practical way to secure and support the workpiece to a

-2-

CS10 specifications

The Bosch Power Tools CS10 is a versatile and powerful circular saw that caters to both professional contractors and DIY enthusiasts. Weighing in at just 10.5 pounds, the CS10 is designed for superior handling and maneuverability on job sites. Its robust construction ensures that it can withstand the rigors of daily use while still providing reliable performance.

One of the standout features of the Bosch CS10 is its 15-amp motor, which delivers an impressive 5,600 RPM, making it efficient for a variety of cutting tasks. This high-performance motor ensures that the saw can tackle even the toughest materials. The CS10 also boasts a 7-1/4-inch cutting blade, providing a maximum cutting depth of 2-7/8 inches at 90 degrees and 2-1/2 inches at 45 degrees. This capacity makes it suitable for cutting through lumber, plywood, and other common building materials effortlessly.

The CS10 is equipped with an integrated dust blower that helps keep the cut line clear, enhancing visibility and accuracy during operation. This feature is particularly beneficial when working in tight spaces or when precise cuts are critical. Additionally, the saw features a built-in laser guide for improved accuracy, allowing users to make straight cuts with confidence.

Ergonomics play a crucial role in the design of the Bosch CS10. The saw features a comfortable, soft-grip handle that reduces fatigue during extended use. The integrated safety brake ensures that the blade stops quickly when the trigger is released, providing an added layer of safety for users.

Another notable characteristic of the CS10 is its durable base plate, crafted from high-quality materials to ensure stability during cuts. The saw also includes an adjustable bevel that allows users to make angled cuts with ease, offering versatility for various projects.

In summary, the Bosch Power Tools CS10 is a powerful and reliable circular saw that combines performance with innovative features. Its robust motor, cutting capacity, and user-friendly design make it an excellent choice for professionals and home improvement enthusiasts alike. Whether you are framing, woodworking, or tackling a renovation project, the CS10 is designed to meet your cutting needs with precision and efficiency.