Bosch Power Tools CS10 manual Protruding blade may cut objects that can cause Kickback

Page 5

BM 1619X00886 3-05 3/20/05 9:27 PM Page 5

Maintain a firm grip with both hands on the saw and position your body and arm to allow you to resist KICKBACK forces.

KICKBACK forces can be controlled by the operator, if proper precautions are taken.

When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or KICKBACK may occur. Investigate and take corrective action to eliminate the cause of blade binding. Wet lumber, green lumber or pressure treated lumber require special attention during cutting operation to prevent KICKBACK. Avoid cutting nails. Inspect for and remove all nails from lumber before cutting.

When restarting a saw in a workpiece, center the saw blade in the kerf and check that saw teeth are not engaged into the material. If saw blade is binding, it may walk up or KICKBACK from the workpiece as the saw is restarted.

Support large panels to minimize the risk of blade pinching and KICKBACK. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel. See “Cutting Large Sheets” in this manual.

Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK.

Blade depth and bevel adjusting locking knobs must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK. Using the saw with an excessive depth of cut setting increases loading on the unit and susceptibility to twisting of the blade in the kerf. It also increases the surface area of the blade available for pinching under conditions of kerf close down.

Use extra caution when making a “Pocket Cut” into existing walls or other blind areas.

The protruding blade may cut objects that can cause KICKBACK.

Some dust created by ! WARNING power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and other masonry products, and

• Arsenic and chromium from chemically- treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

-5-

Page 4 Page 6
Image 5
Page 4 Page 6
Contents For English Parlez-vous français? Read Before Using Lire avant usageSee Voir Ver páginaElectrical Safety Power Tool Safety RulesPersonal Safety Work AreaService Safety Rules for Circular SawsVARI-TORQUE Clutch Causes and Operator Prevention KickbackProtruding blade may cut objects that can cause Kickback Symbols Circular Saw Functional Description and SpecificationsMeasures reduce the risk of starting the tool accidentally Maximum CapacitiesVARI-TORQUE Clutch AssemblyAttaching the Blade Bevel Adjustment Depth AdjustmentOperating Instructions Cutting Angle CheckCutting MASONRY/METAL SwitchGeneral Cuts Cutting Large Sheets Pocket CutsFoot Lower Guard Wrong RightCleaning MaintenanceCare of Blades AccessoriesAire de travail Règles de Sécurité GénéralesSécurité électrique Sécurité des personnesRéparation Consignes de sécurité pour scies circulairesUtilisation et entretien des outils Embrayage VARI-TORQUE Causes ET PRÉVENTION, PAR Lopérateur DU RebondLe plomb provenant des peintures à base de plomb Symboles Scie circulaire Description fonctionnelle et spécificationsCapacités maximales Numéro modèle CS10 Lame 184 mm Moyeu de lame Rond 5/8Montage DE LA Lame AssemblageEmbrayage « VARI-TORQUE » Garde SupérieurRéglage DE LA Profondeur DE Coupe Consignes de fonctionnementVérification DE L’ANGLE DE Coupe Réglage DE LA Coupe EN BiseauSciage DES Matériaux DE Maçonnerie ET DES Métaux InterrupteurCoupes Régulierès La lame Coupes EN GuichetCoupe DE Grandes Feuilles Semelle Levier DE Levage DU Garde INFÉRIEURENCOCHE-GUIDENettoyage EntretienCertains Agents AccessoiresEt certains Entretien DES LamesArea de trabajo Normas de seguridad para herramientas mecánicasSeguridad eléctrica Seguridad personalServicio Normas de seguridad para sierras circularesEmbrague DE PAR Motor Variable Causas DEL Retroceso Y SU Prevencion POR EL OperadorBM 1619X00886 3-05 3/20/05 928 PM De Ni-Cd SímbolosCon aislamiento doble Sierra circular Descripción funcional y especificacionesRiesgo de arrancar la herramienta accidentalmente Número modelo CS10 Hoja 184 mmEmbrague DE PAR Motor Variable EnsamblajeColocacion DE LA Hoja Ajuste DE Inclinación Instrucciones de funcionamientoHoja en la pieza de trabajo y a la disminución en la Base Hoja Palanca DE Ajuste DE InclinaciónGuía DE Interruptor Guía DE LíneaCortes Generales Movimiento libre del protector inferiorIncorrecto Correcto Cortes DE BolsillosCorte DE Planchas Grandes Limpieza MantenimientoHoja = equipo estándar Llave AccesoriosCuidado DE LAS Hojas BM 1619X00886 3-05 3/20/05 928 PM Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools
Related manuals
Manual 4 pages 32.82 Kb

CS10 specifications

The Bosch Power Tools CS10 is a versatile and powerful circular saw that caters to both professional contractors and DIY enthusiasts. Weighing in at just 10.5 pounds, the CS10 is designed for superior handling and maneuverability on job sites. Its robust construction ensures that it can withstand the rigors of daily use while still providing reliable performance.

One of the standout features of the Bosch CS10 is its 15-amp motor, which delivers an impressive 5,600 RPM, making it efficient for a variety of cutting tasks. This high-performance motor ensures that the saw can tackle even the toughest materials. The CS10 also boasts a 7-1/4-inch cutting blade, providing a maximum cutting depth of 2-7/8 inches at 90 degrees and 2-1/2 inches at 45 degrees. This capacity makes it suitable for cutting through lumber, plywood, and other common building materials effortlessly.

The CS10 is equipped with an integrated dust blower that helps keep the cut line clear, enhancing visibility and accuracy during operation. This feature is particularly beneficial when working in tight spaces or when precise cuts are critical. Additionally, the saw features a built-in laser guide for improved accuracy, allowing users to make straight cuts with confidence.

Ergonomics play a crucial role in the design of the Bosch CS10. The saw features a comfortable, soft-grip handle that reduces fatigue during extended use. The integrated safety brake ensures that the blade stops quickly when the trigger is released, providing an added layer of safety for users.

Another notable characteristic of the CS10 is its durable base plate, crafted from high-quality materials to ensure stability during cuts. The saw also includes an adjustable bevel that allows users to make angled cuts with ease, offering versatility for various projects.

In summary, the Bosch Power Tools CS10 is a powerful and reliable circular saw that combines performance with innovative features. Its robust motor, cutting capacity, and user-friendly design make it an excellent choice for professionals and home improvement enthusiasts alike. Whether you are framing, woodworking, or tackling a renovation project, the CS10 is designed to meet your cutting needs with precision and efficiency.
Top Page Image Contents