Bosch Power Tools CS10 manual Operating Instructions, Depth Adjustment, Cutting Angle Check

Page 9

BM 1619X00886 3-05 3/20/05 9:27 PM Page 9

Operating Instructions

DEPTH ADJUSTMENT

Your saw is equipped with a depth detent system that will stop the foot at 2x, 3/4", 1/2", and 1/4" standard lumber depths.

Disconnect plug from power source. Loosen the depth adjustment lever located in the housing of saw. Hold the foot down with one hand and raise or lower saw by the handle.

FIG. 3

CALIBRATED

DEPTH BRACKET

ADJUSTABLE

DEPTH LEVER

Tighten lever at the depth setting desired. Check desired depth (Fig. 3).

Your saw also features a adjustable depth adjustment lever for consistent locking. To adjust, simply pull outward on lever and reposition to desired position (Fig.3).

Not more than one tooth length of the blade should extend below the material to be cut, for minimum splintering (Fig. 4).

FIG. 4

2

1 FOOT

ONE TOOTH LENGTH SHOULD

PENETRATE WOOD FOR MINIMUM SPLINTERING

90° CUTTING ANGLE CHECK

Disconnect plug from power source. Set foot to maximum depth of cut setting. Loosen bevel adjustment lever, set to 0° on quadrant, retighten lever and check for 90° angle between the blade and bottom plane of foot with a square (Fig. 5). Make adjustments by turning the small alignment screw from bottom side of foot, if necessary.

FIG. 5

 

BEVEL

 

 

ADJUSTMENT

 

 

LEVER

FOOT

 

 

BLADE

90°

ALIGNMENT

 

SCREW

 

 

BEVEL ADJUSTMENT

Your saw is equipped with a bevel detent system that will stop the foot at 22.5°, and 45° angles.

Disconnect plug from power source. The foot can be adjusted up to 56° by loosening the bevel adjustment lever at the front of the saw. Align to desired angle on calibrated quadrant. Then tighten bevel adjustment lever (Fig. 6).

Your saw also features a adjustable bevel adjustment lever for consistent locking. To adjust, simply pull outward on lever and reposition to desired position (Fig. 1).

Because of the increased amount of blade engagement in the work and decreased

stability of the foot, blade binding may occur. Keep the saw steady and the foot firmly on the workpiece.

FIG. 6

QUADRANT

BEVEL

ADJUSTMENT

LEVER

-9-

Image 9
Contents For English Parlez-vous français? Read Before Using Lire avant usageSee Voir Ver páginaElectrical Safety Power Tool Safety RulesPersonal Safety Work AreaService Safety Rules for Circular SawsVARI-TORQUE Clutch Causes and Operator Prevention KickbackProtruding blade may cut objects that can cause Kickback Symbols Circular Saw Functional Description and SpecificationsMeasures reduce the risk of starting the tool accidentally Maximum CapacitiesAssembly Attaching the BladeVARI-TORQUE Clutch Bevel Adjustment Depth AdjustmentOperating Instructions Cutting Angle CheckSwitch General CutsCutting MASONRY/METAL Cutting Large Sheets Pocket CutsFoot Lower Guard Wrong RightCleaning MaintenanceCare of Blades AccessoriesAire de travail Règles de Sécurité GénéralesSécurité électrique Sécurité des personnesConsignes de sécurité pour scies circulaires Utilisation et entretien des outilsRéparation Embrayage VARI-TORQUE Causes ET PRÉVENTION, PAR Lopérateur DU RebondLe plomb provenant des peintures à base de plomb Symboles Scie circulaire Description fonctionnelle et spécificationsCapacités maximales Numéro modèle CS10 Lame 184 mm Moyeu de lame Rond 5/8Montage DE LA Lame AssemblageEmbrayage « VARI-TORQUE » Garde SupérieurRéglage DE LA Profondeur DE Coupe Consignes de fonctionnementVérification DE L’ANGLE DE Coupe Réglage DE LA Coupe EN BiseauInterrupteur Coupes RégulierèsSciage DES Matériaux DE Maçonnerie ET DES Métaux La lame Coupes EN GuichetCoupe DE Grandes Feuilles Semelle Levier DE Levage DU Garde INFÉRIEURENCOCHE-GUIDENettoyage EntretienCertains Agents AccessoiresEt certains Entretien DES LamesArea de trabajo Normas de seguridad para herramientas mecánicasSeguridad eléctrica Seguridad personalServicio Normas de seguridad para sierras circularesEmbrague DE PAR Motor Variable Causas DEL Retroceso Y SU Prevencion POR EL OperadorBM 1619X00886 3-05 3/20/05 928 PM Símbolos Con aislamiento dobleDe Ni-Cd Sierra circular Descripción funcional y especificacionesRiesgo de arrancar la herramienta accidentalmente Número modelo CS10 Hoja 184 mmEnsamblaje Colocacion DE LA HojaEmbrague DE PAR Motor Variable Ajuste DE Inclinación Instrucciones de funcionamientoHoja en la pieza de trabajo y a la disminución en la Base Hoja Palanca DE Ajuste DE InclinaciónGuía DE Interruptor Guía DE LíneaCortes Generales Movimiento libre del protector inferiorCortes DE Bolsillos Corte DE Planchas GrandesIncorrecto Correcto Limpieza MantenimientoAccesorios Cuidado DE LAS HojasHoja = equipo estándar Llave BM 1619X00886 3-05 3/20/05 928 PM Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools
Related manuals
Manual 4 pages 32.82 Kb

CS10 specifications

The Bosch Power Tools CS10 is a versatile and powerful circular saw that caters to both professional contractors and DIY enthusiasts. Weighing in at just 10.5 pounds, the CS10 is designed for superior handling and maneuverability on job sites. Its robust construction ensures that it can withstand the rigors of daily use while still providing reliable performance.

One of the standout features of the Bosch CS10 is its 15-amp motor, which delivers an impressive 5,600 RPM, making it efficient for a variety of cutting tasks. This high-performance motor ensures that the saw can tackle even the toughest materials. The CS10 also boasts a 7-1/4-inch cutting blade, providing a maximum cutting depth of 2-7/8 inches at 90 degrees and 2-1/2 inches at 45 degrees. This capacity makes it suitable for cutting through lumber, plywood, and other common building materials effortlessly.

The CS10 is equipped with an integrated dust blower that helps keep the cut line clear, enhancing visibility and accuracy during operation. This feature is particularly beneficial when working in tight spaces or when precise cuts are critical. Additionally, the saw features a built-in laser guide for improved accuracy, allowing users to make straight cuts with confidence.

Ergonomics play a crucial role in the design of the Bosch CS10. The saw features a comfortable, soft-grip handle that reduces fatigue during extended use. The integrated safety brake ensures that the blade stops quickly when the trigger is released, providing an added layer of safety for users.

Another notable characteristic of the CS10 is its durable base plate, crafted from high-quality materials to ensure stability during cuts. The saw also includes an adjustable bevel that allows users to make angled cuts with ease, offering versatility for various projects.

In summary, the Bosch Power Tools CS10 is a powerful and reliable circular saw that combines performance with innovative features. Its robust motor, cutting capacity, and user-friendly design make it an excellent choice for professionals and home improvement enthusiasts alike. Whether you are framing, woodworking, or tackling a renovation project, the CS10 is designed to meet your cutting needs with precision and efficiency.