Craftsman 315.21829 manual Unpacking, To Open the LEG Stand, See Figures 7, Base

Page 16

UNPACKING

Thisproduct requiresassembly.

•Carefully lift the asw from the carton and place it on a level work surface.

NOTE=This tool is heavy.To avoid back injury,keep your knees bent and lift with your legs, not your back,

and do not lift saw without help.

•Inspect the tool carefullyto make sure no breakage or darnags occurred duringshipping.

•Do not discard the packing material untilyou have caref_Jttyinspected and sstistacto_tyoperated the too_.

•The _aw is factory set far accurate cutt'_ngAfter. assembling it, check for accuracy.If shipping has influenced _e settings, refer to specificprocedures expta'medin _is manual.

•If any parts are damaged or missing, plasea call 1-800-932-3188 for ass]stance.

_" WARNING: if any parts are missing, do not operate th_stoo_ unt_the missing parts are replaced. Failure to do so could rssultin possibleserious personal injury.

_1= WARNING: Do not attempt to modify this tool or create accessories not recommendedfor use

with this tool. Any such aiteratlonor modification is misuse and could resultin a hazardous condition

leading to possible se_oL;spersonalin)ury.

AWARNING: Do not connectto power supply until assembly is complete. Fa(lursto comply could result in accidental starting and possible seriouspersonal injury.

_1= WARNING: Do not lift the saw without help. Hold it close to your body. Keep your knees bent and

(iftwith yourlegs, not your back. Ignoringthese precautions can resultin back injury.

A

Am, WARNING: Never stand d}rs_')yin line with the blade or allow hands to corns closer than 3 in. to the blade. Do not reach over or across the blade. Failure

to heed this warning can resultin serious personal iniury.

A

me, WARNING" To avoid seriouspersonal injury, always

make sure the table saw is securely mounted to

this leg stand. NEVER remove the saw from the 1eg stand.

TO OPEN THE LEG STAND

See Figures 7- 8.

•Grasp the grips on the saw table and s_and it upright as shown in figure 7 be(ow.

•Step on the release ]everand pull the grips toward you at the same time.

•Once the leg stand is released from the release lever, ease the leg s_n rttoward the _ocr by pashlngth_ grips toward the floor.

•Withyourhandsonthegr_ps, pushthslegstand_owards the ground untilthe _.bis saw is in an upright pos'_tion. NOTE: The release leverwill close over the center brace lockingthe leg stand in an upright poslton.

GRIPS

SAW

 

BASE

RELEASE LEG,STAND

LEVER

Fig. 7

cENTER

BRACE

Fig, 8

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 10 in. Table SAW Customer Help Line 983000-693 15-05ONE Year Full Warranty on Craftsman Tool Always Keep the Blade Guard and Riving Keep Blades CLEAN, SHARP, AndwithKNIFE/SPREADER/SPLITTER in Place and in working order Blade Coasts After Being Turned OFF Before Making a CUT, be Sure ALL Adjust Ments are SecureAlways USE a Push Stick for Ripping NAR Avoid Awkward Operations and Hand Save These INSTRUCTIONS. Refer to themMinutes Time Symbol Name Desig NATION/EXPLANATIO NJmin Symbol Signal Awarning Caiion Meaning Your nearest Authorized Service Center for repairWhen servicing, use onyidenticalreplacement parts Servicingrequires extreme care and knowledgeSAW Receptacle Motor Power Electrical Connection Speed and WiringExtension Cords Grounding InstructionsCutter Head planers and Jointera Number ofturnscompletedby a spinningobjectin one minute120 V, 60 Hz AC only Product SpecficationsAmperes Know Your Table SAW See FigureOperatingcomponents Blades Combinationflatblade SquarescrewdriverThefollowing items are included with your table saw Small BadeWrench@ D Thefolidwing items are includedwith your table sawUnpacking To Open the LEG StandSee Figures 7 BaseTOSECURE/LEVELTHESAW See F-igum9See Figures 10 Sliding miter tableSee F-tre Bevel HandleSee Figures 13 TOUNLOCK/MOVETHERAILS ReleaseTochecksawbladeinstallation To Install the Sliding Miter Table and Miter FenceSee Figures fg Lockingclamps Throat Plate Small Wrench Large BladeoSee Flours21 SeeRIW ANTI-KICKBACKSHIMS HNS Applications Not recommended can resultin serious personal injuryBasic Operation of the Table SAW Causes of Kickback Avoiding KickbackUse the right type of blade for the cut being made Cutting AidsCutting Tips Types of CutsRIP CUT Mitercut Compoundbevelmitercut HOW to Make a Featherboard Diameter HOW to Mount a FeatherboardFeatherboard See F/gumChecking Sliding Miter Table and Making Adjustments TochangethebladedepthSee Rgure Not Front of miter base is on infead se of sawTo Adjust The Miter Base sectionthat follows Check Miter Fence AlignmentTo Adjust the Miter Base Mitertable Slides To Adjust the Miter FenceTo Adjust Quick Stop StopSee F=Jgure39 Makingcuts Test cut on scrap wood firstMaking a Cross CUT See Figures40.saw for the cut work Fence Making a Miter CUTSee F-agure43 See Ffeures44Fiouspersonalinjury BEVELRiP. CUT 8LADE Angled Scale Making a Compound Bevel Miter CUTMaking a Large Panel CUT See gMaking a Dado CUT NON-THROUGHCUT Guard Blade Removed Push StickAccessory Table Usage Knobbolt Nutbetween Adjustment ScrewsRear Table Clampng BracketToinstallguidefencebrackets NUTTo Install BIT and Throat Plate ToinstallrouterSee Ftgure55 To Replace the Blade See Figures57Throm Plate Blade Bladethroatplate Rmng Knife Blaie Large Small WrenchSee Figures 60 Framing Square Rivingblade KnifeTo Adjust the Miter Gauge To Adjust the Bevel Locking Lever HEIGHT/BEVELADJUSTING Hanowheel Socket Hdsew SetscrewBlade Screws HANDLEFigToaugnthemiterlockingclamps ScrewLocker Bracket Assembly GeneralLubrication ElevatingshaftSolution CauseProblem Cause Check and adjustthe rip fence Reeharpenor set bladeLockinglever is not at full left position BJadenot proper for rip cutFORlEG Standassembly Craftsman 10 in. Table SAW Model noParts List Figure a Craftsman 10 in. Table SAW Model NO, 3t5.2t8290Parts List QtyCraftsman 10 in. Table SAW- Model no Key PartNumber Deecdptlon Description QtyScrew Craftsman t0 in. Table SAW Model no t5.218290 Figure F Miter Gauge Assembly Craftsman 10 in. Table SAW Mooel noA181014601 Craftsman t0 in. Table SAW Model no FiguregKey Part Number DescdpUon Qty Description Parts List for Figure G411061704 Call anytime, day or night U.S.A. and Canada Call anytime, day or night U.S.A. only

315.21829 specifications

The Craftsman 315.21829 is a versatile and robust power tool designed for a variety of home improvement and woodworking tasks. Known for its reliability, this model is part of the Craftsman family, a brand that has built a reputation for offering user-friendly tools that provide high performance without compromising on safety and comfort.

One of the standout features of the Craftsman 315.21829 is its powerful motor, delivering ample horsepower to tackle demanding jobs. Whether you are cutting, sanding, or drilling, this tool ensures efficient operation and quick results. The design reflects an emphasis on power and precision, enabling users to achieve professional-quality finishes.

The ergonomic design of the Craftsman 315.21829 includes a comfortable grip, which reduces fatigue during extended use. This aspect is particularly important for both DIY enthusiasts and professionals who often spend long hours working on projects. The lightweight nature of the tool also contributes to its ease of use, making it suitable for a wide range of applications around the home and workshop.

A key technological feature of the Craftsman 315.21829 is its variable speed control, allowing users to adjust the tool's speed according to the specific requirements of the task at hand. This flexibility enhances control and precision, especially when working with delicate materials or intricate designs. The built-in safety features provide added peace of mind, ensuring that the tool operates under safe conditions at all times.

Another highlight is the compatibility with a wide range of accessories, which enhances the versatility of the Craftsman 315.21829. Users can easily switch between tasks, whether they are drilling holes, driving screws, or finishing surfaces. This adaptability makes it a valuable addition to any toolkit.

Overall, the Craftsman 315.21829 stands out for its combination of power, versatility, and user-friendly design. It caters to both seasoned professionals and DIY novices, enabling a wide array of projects to be completed with ease and precision. With its robust features and reliable performance, this tool continues to be a favorite in the realm of home improvement and woodworking.
Top Page Image Contents